Home / Cisco / 200-301

Question list

List of questions

Question 1

(0)

DRAG DROP Drag and drop the descriptions of file-transfer protocols from the left onto the correct protocols on the right.

Question 2

(0)

DRAG DROP Drag and drop the IPv4 network subnets from the left onto the correct usable host ranges on the right.

Question 3

(0)

DRAG DROP Refer to the exhibit. Drag and drop the networking parameters from the left onto the correct values on the right.

Question 4

(0)

DRAG DROP Drag the descriptions of IP protocol transmissions from the left onto the IP traffic types on the right.

Question 5

(0)

DRAG DROP Drag and drop the application protocols from the left onto the transport protocols that it uses on the right.

Question 6

(0)

DRAG DROP Drag and drop the TCP/IP protocols from the left onto their primary transmission protocols on the right.

Question 7

(0)

DRAG DROP Drag and drop the characteristics of network architectures from the left onto the type of architecture on the right.

Question 8

(0)

DRAG DROP Drag and drop the networking parameters from the left on to the correct values on the right.

Question 9

(0)

DRAG DROP Drag and drop the TCP or UDP details from the left onto their corresponding protocols on the right.

Question 10

(0)

DRAG DROP Drag and drop the IPv6 addresses from the left onto the corresponding address types on the right.

Question 897 - 200-301 discussion

All physical cabling is in place. A company plans to deploy 32 new sites.

The sites will utilize both IPv4 and IPv6 networks.

1 . Subnet 172.25.0.0/16 to meet the subnet requirements and maximize the number of hosts

Using the second subnet

* Assign the first usable IP address to e0/0 on Sw101

* Assign the last usable IP address to e0/0 on Sw102

Subnet to meet the subnet requirements and maximize the number of hosts

Using the second subnet

* Assign an IPv6 GUA using a unique 64-Bit interface identifier on e0/0 on Sw101

* Assign an IPv6 GUA using a unique 64-Bit interface identifier on eO/O on swi02

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

* Refer to the Tasks tab to view the tasks for this lab item.

* Refer to the Topology tab to access the device console(s) and perform the tasks.

* Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

* All necessary preconfigurations have been applied.

* Do not change the enable password or hostname for any device.

* Save your configurations to NVRAM before moving to the next item.

* Click Next at the bottom of the screen to submit this lab and move to the next question.

* When Next is clicked, the lab closes and cannot be reopened.

See the Explanation below

Suggested answer: A

Explanation:

To subnet 172.25.0.0/16 to meet the subnet requirements and maximize the number of hosts, you need to determine how many bits you need to borrow from the host portion of the address to create enough subnets for 32 sites. Since 32 is 2^5, you need to borrow 5 bits, which means your new subnet mask will be /21 or 255.255.248.0. To find the second subnet, you need to add the value of the fifth bit (32) to the third octet of the network address (0), which gives you 172.25.32.0/21 as the second subnet. The first usable IP address in this subnet is 172.25.32.1, and the last usable IP address is 172.25.39.254.

To assign the first usable IP address to e0/0 on Sw101, you need to enter the following commands on the device console:

Sw101#configure terminal Sw101(config)#interface e0/0 Sw101(config-if)#ip address 172.25.32.1 255.255.248.0 Sw101(config-if)#no shutdown Sw101(config-if)#end

To assign the last usable IP address to e0/0 on Sw102, you need to enter the following commands on the device console:

Sw102#configure terminal Sw102(config)#interface e0/0 Sw102(config-if)#ip address 172.25.39.254 255.255.248.0 Sw102(config-if)#no shutdown Sw102(config-if)#end

To subnet an IPv6 GUA to meet the subnet requirements and maximize the number of hosts, you need to determine how many bits you need to borrow from the interface identifier portion of the address to create enough subnets for 32 sites. Since 32 is 2^5, you need to borrow 5 bits, which means your new prefix length will be /69 or ffff:ffff:ffff:fff8::/69 (assuming that your IPv6 GUA has a /64 prefix by default). To find the second subnet, you need to add the value of the fifth bit (32) to the fourth hextet of the network address (0000), which gives you xxxx:xxxx:xxxx:0020::/69 as the second subnet (where xxxx:xxxx:xxxx is your IPv6 GUA prefix). The first and last IPv6 addresses in this subnet are xxxx:xxxx:xxxx:0020::1 and xxxx:xxxx:xxxx:0027:ffff:ffff:ffff:fffe respectively.

To assign an IPv6 GUA using a unique 64-bit interface identifier on e0/0 on Sw101, you need to enter the following commands on the device console (assuming that your IPv6 GUA prefix is 2001:db8::/64):

Sw101#configure terminal Sw101(config)#interface e0/0 Sw101(config-if)#ipv6 address 2001:db8::20::1/69 Sw101(config-if)#no shutdown Sw101(config-if)#end

To assign an IPv6 GUA using a unique 64-bit interface identifier on e0/0 on Sw102, you need to enter the following commands on the device console (assuming that your IPv6 GUA prefix is 2001:db8::/64):

Sw102#configure terminal Sw102(config)#interface e0/0 Sw102(config-if)#ipv6 address 2001:db8::27::fffe/69 Sw102(config-if)#no shutdown Sw102(config-if)#end

Show Answer

asked 07/10/2024

PKE Holding AG Leitgeb

36 questions

Your answer: A

0 comments

Sorted by