ExamGecko
Search Search Login
Home Home / Cisco / 300-410
Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. Refer to the exhibit. R1 uses SP1 as the primary path. A network engineer must force all SSH traffic generated from R1 toward SP2. Which configuration accomplishes the task?
LAB SIMULATION WAN CORE MGMT
Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
Refer to the exhibit. Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?
Refer to the exhibit. Refer to the exhibit After an engineer modified the configuration for area 7 to permit type 1 2 and 7 LSAs only users connected to router R9 reported that they could no longer access the internet. Which configuration restores internet access to users on R9 and permits only LSA type 1,2, and 7? A) B) C) D)
Refer to the exhibit. Refer to the exhibit. Which configuration resolves the issue? A) B) C) D)
An engineer configured a router with this configuration ip access-hst DENY TELNET 10 deny tcp any any eq 23 log-input The router console starts receiving log message :%SEC-6-IPACCESSLOGP: list DENY_TELNET denied tcp 192.168.1.10(1022)(FastEthernet1/0 D508.89gb.003f) ->192.168.2.20(23), 1 packet" Which action stops messages on the console while still denying Telnet?
Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?
Refer to the exhibit. Refer to the exhibit. The R1 routing table has the prefixes for the FTP1 and FTP2 file servers. A network engineer must configure the R1 with these requirements: Host1 must use the FTP1 fileserver. Host2 must use the FTP2 fileserver. Which configuration meets the requirement on R1?

Question 68 - 300-410 discussion

Report
Export

Exhibit:

BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue?

(Choose two)

A.

Configure BGP in the COPP-CRITICAL-7600 ACL

Answers
A.

Configure BGP in the COPP-CRITICAL-7600 ACL

B.

Configure a higher value for CIR under the default class to allow more packets during peak traffic

Answers
B.

Configure a higher value for CIR under the default class to allow more packets during peak traffic

C.

Configure a higher value for CIR under the class COPP-CRITICAL-7600

Answers
C.

Configure a higher value for CIR under the class COPP-CRITICAL-7600

D.

Configure a three-color policer instead of two-color policer under class COPP-CRITICAL- 7600

Answers
D.

Configure a three-color policer instead of two-color policer under class COPP-CRITICAL- 7600

E.

Configure IP CEF to CoPP policy and BGP to work

Answers
E.

Configure IP CEF to CoPP policy and BGP to work

Suggested answer: A, B

Explanation:

The policy-map COPP-7600 only rate-limit HTTP & HTTPS traffic (based on the ACLconditions) so any BGP packets will be processed in the class "class-default", which dropsexceeded BGP packets. Therefore we have two ways to solve this problem:

+ Add BGP to the ACL with the statement "permit tcp any any eq bgp"

+ Configure higher value for CIR in default class as 2Mbps is too low for web traffic (http & https)

Show Answer
asked 07/10/2024
mark obrien
43 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms