Home

Home / Cisco / 300-410

Question list

List of questions

Question 1

(0)

Refer to the exhibit. Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve th

Question 2

(0)

Refer to the exhibit. Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?

Question 3

(0)

R2 has a locally originated prefix 192.168.130.0/24 and has these configurations: What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the n

Question 4

(0)

Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?

Question 5

(0)

Refer to the exhibit. The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?

Question 6

(0)

Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?

Question 7

(0)

Refer to the exhibit. An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missi

Question 8

(0)

Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as a

Question 9

(0)

What is a prerequisite for configuring BFD?

Question 10

(0)

Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibit. Refer to the exhibit. R1 uses SP1 as the primary path. A network engineer must force all SSH traffic generated from R1 toward SP2. Which configuration accomplishes the task?

LAB SIMULATION WAN CORE MGMT

Refer to the exhibit. Refer to the exhibit After an engineer modified the configuration for area 7 to permit type 1 2 and 7 LSAs only users connected to router R9 reported that they could no longer access the internet. Which configuration restores internet access to users on R9 and permits only LSA type 1,2, and 7? A) B) C) D)

Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?

Refer to the exhibit. Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

Refer to the exhibit. Refer to the exhibit. Which configuration resolves the issue? A) B) C) D)

An engineer configured a router with this configuration ip access-hst DENY TELNET 10 deny tcp any any eq 23 log-input The router console starts receiving log message :%SEC-6-IPACCESSLOGP: list DENY_TELNET denied tcp 192.168.1.10(1022)(FastEthernet1/0 D508.89gb.003f) ->192.168.2.20(23), 1 packet" Which action stops messages on the console while still denying Telnet?

Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?

Refer to the exhibit. Refer to the exhibit. The R1 routing table has the prefixes for the FTP1 and FTP2 file servers. A network engineer must configure the R1 with these requirements: Host1 must use the FTP1 fileserver. Host2 must use the FTP2 fileserver. Which configuration meets the requirement on R1?

Question 143 - 300-410 discussion

Report

Refer to the exhibit. Which action restores the routes from neighbors while still filtering 1.1.1.0/24?

A.

Add a second line in the access list to permit any.

B.

Modify the route map to permit the access list instead of deny it

C.

Modify the access list to deny instead of permit it.

D.

Add a second sequence in the route map permit 20

Show Answer

asked 07/10/2024

Luis Campoy

41 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first