ExamGecko
Search Search Login
Home Home / Cisco / 300-410
Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. Refer to the exhibit. R1 uses SP1 as the primary path. A network engineer must force all SSH traffic generated from R1 toward SP2. Which configuration accomplishes the task?
LAB SIMULATION WAN CORE MGMT
Refer to the exhibit. Refer to the exhibit After an engineer modified the configuration for area 7 to permit type 1 2 and 7 LSAs only users connected to router R9 reported that they could no longer access the internet. Which configuration restores internet access to users on R9 and permits only LSA type 1,2, and 7? A) B) C) D)
Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
Refer to the exhibit. Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?
Refer to the exhibit. Refer to the exhibit. Which configuration resolves the issue? A) B) C) D)
Refer to the exhibit. An administrator must configure the router with OSPF for IPv4 and IPv6 networks under a single process. The OSPF adjacencies are not established and did not meet the requirement. Which action resolves the issue?
An engineer configured a router with this configuration ip access-hst DENY TELNET 10 deny tcp any any eq 23 log-input The router console starts receiving log message :%SEC-6-IPACCESSLOGP: list DENY_TELNET denied tcp 192.168.1.10(1022)(FastEthernet1/0 D508.89gb.003f) ->192.168.2.20(23), 1 packet" Which action stops messages on the console while still denying Telnet?
Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?

Question 394 - 300-410 discussion

Report
Export

An engineer configures PBR on R5 and wants to create a policy that matches traffic destined toward 10.10.10.0/24 and forward 10.1.1.1. The traffic must also have its IP precedence set to 5.All other traffic should be forward toward 10.1.1.2 and have its IP precedence set to 0.Which configuration meets the requirements?

A.

access-list 1 permit 10.10.10.0 0.0.0.255

access-list 2 permit any

route-map CCNP permit 10

match ip address 1

set ip next-hop 10.1.1.1

set ip precedence 5

!

route-map CCNP permit 20

match ip address 2

set ip next-hop 10.1.1.2

set ip precedence 0route-map CCNP permit 30

Answers
A.

access-list 1 permit 10.10.10.0 0.0.0.255

access-list 2 permit any

route-map CCNP permit 10

match ip address 1

set ip next-hop 10.1.1.1

set ip precedence 5

!

route-map CCNP permit 20

match ip address 2

set ip next-hop 10.1.1.2

set ip precedence 0route-map CCNP permit 30

B.

access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address 100 set ip next-hop 10.1.1.1 set ip precedence 0 ! route-map CCNP permit 20

set ip next-hop 10.1.1.2

set ip precedence 5

!

route-map CCNP permit 30

Answers
B.

access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address 100 set ip next-hop 10.1.1.1 set ip precedence 0 ! route-map CCNP permit 20

set ip next-hop 10.1.1.2

set ip precedence 5

!

route-map CCNP permit 30

C.

access-list 1 permit 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address 1 set ipnexthop 10.1.1.1 set ip precedence 5 ! route-map CCNP permit 20 set ip next-hop 10.1.1.2 set ip

precedence 0

Answers
C.

access-list 1 permit 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address 1 set ipnexthop 10.1.1.1 set ip precedence 5 ! route-map CCNP permit 20 set ip next-hop 10.1.1.2 set ip

precedence 0

D.

access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address

100 set ip next-hop 10.1.1.1 set ip precedence 5 ! route-map CCNP permit 20 set ip next-hop 10.1.1.2 set ip precedence 0

Answers
D.

access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address

100 set ip next-hop 10.1.1.1 set ip precedence 5 ! route-map CCNP permit 20 set ip next-hop 10.1.1.2 set ip precedence 0

Suggested answer: D
Show Answer
asked 07/10/2024
Maxim Shpakov
41 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms