ExamGecko
Search Search Login
Home Home / Cisco / 300-410
Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. Refer to the exhibit. R1 uses SP1 as the primary path. A network engineer must force all SSH traffic generated from R1 toward SP2. Which configuration accomplishes the task?
LAB SIMULATION WAN CORE MGMT
Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
Refer to the exhibit. Refer to the exhibit After an engineer modified the configuration for area 7 to permit type 1 2 and 7 LSAs only users connected to router R9 reported that they could no longer access the internet. Which configuration restores internet access to users on R9 and permits only LSA type 1,2, and 7? A) B) C) D)
Refer to the exhibit. Refer to the exhibit. Which configuration resolves the issue? A) B) C) D)
An engineer configured a router with this configuration ip access-hst DENY TELNET 10 deny tcp any any eq 23 log-input The router console starts receiving log message :%SEC-6-IPACCESSLOGP: list DENY_TELNET denied tcp 192.168.1.10(1022)(FastEthernet1/0 D508.89gb.003f) ->192.168.2.20(23), 1 packet" Which action stops messages on the console while still denying Telnet?
Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?
Refer to the exhibit. Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?
Refer to the exhibit. Refer to the exhibit. The R1 routing table has the prefixes for the FTP1 and FTP2 file servers. A network engineer must configure the R1 with these requirements: Host1 must use the FTP1 fileserver. Host2 must use the FTP2 fileserver. Which configuration meets the requirement on R1?

Question 529 - 300-410 discussion

Report
Export

Refer to the exhibit.

Refer to me exhibit Traffic from R3 to the central site does not use alternate paths when R3 cannot reach 10 10 10 2 Traffic on R3 destined to R4 takes an alternate route via 10 10 10.6 when 10 10 10 4 is not accessible from R3 Which configuration switches traffic destined to 10 10 10 2 from R3 on the alternate path''

A.

R3(config)#ip route 192.168.10.1 255.255.265.255 10.10.10.2 track 20

Answers
A.

R3(config)#ip route 192.168.10.1 255.255.265.255 10.10.10.2 track 20

B.

R2(config)#ip route 10.10 10 3 255 255.255 255 10.0.0.6

Answers
B.

R2(config)#ip route 10.10 10 3 255 255.255 255 10.0.0.6

C.

R3(config)#track( 20 ip sla 20 reachability

Answers
C.

R3(config)#track( 20 ip sla 20 reachability

D.

R6(config)#ip route 10.10.10 3 255.255.255.255 10.0.0.30

Answers
D.

R6(config)#ip route 10.10.10 3 255.255.255.255 10.0.0.30

Suggested answer: A
Show Answer
asked 07/10/2024
Ali Reza Azmi
43 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms