Home

Home / Cisco / 300-510

Question list

List of questions

Question 1

(0)

Refer to the exhibit. Which tree does multicast traffic follow?

Question 2

(0)

Refer to the exhibit. After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?

Question 3

(0)

Refer to the exhibit. Which effect of this configuration is true?

Question 4

(0)

Refer to the exhibit. A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement blo

Question 5

(0)

Refer to the exhibit. A network operator is getting the route for 10.11.11 0/24 from two upstream providers on #XR3. The network operator must configure #XR3 to force the 10.11.11.0/24 prefix to

Question 6

(0)

Refer to the exhibit. After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?

Question 7

(0)

A network consultant is troubleshooting IS-IS instances to identify why a routing domains is having communication problems between the two instances. Which description of the possible cause of issue

Question 8

(0)

What is used by SR-TE to steer traffic through the network?

Question 9

(0)

For which reason can two devices fail to establish an OSPF neighbor relationship?

Question 10

(0)

Refer to the exhibit. Which LSA type is indicated by this router output?

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibit.

Refer to the exhibit. After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration?

Refer to the exhibit. Refer to the exhibit. Users connected to an application on 1.1.1.1 via routers CE1 and CE2 are complaining of frequent disconnections. While troubleshooting the issue, a network engineer with an employee ID: 4333:96:916 determined that the application itself is working normally, but the link connected to the 1.1.1.1 application is flapping. The users on CE1 and CE2 are accessing applications on 2.2.2.2 without difficulty. Which action resolves the issue?

Refer to the exhibit Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?

Refer to the exhibit. Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)

An ISP has an MPLS VPN-based network with 12 PE routers. How many peerings are required between the 12 routers if the engineer has not configured route reflectors?

Refer to the exhibit. Which LSA type is indicated by this router output?

An engineer is troubleshooting a connectivity issue across the MPLS network and is verifying the forwarding behavior of packets. Which table does the engineer look at to verify the forwarding behavior of an IP packet as it enters the MPLS network at the ingress LSR?

Refer to the exhibit. Refer to the exhibit MPLS traffic from the packet core that is connected to router RX (10 10 101) to the radio network that is connected to router RB (10 10 10 6) uses the longer route RB R2 RY RX RX and R2 are configured with a default value of LDP hello and hold intervals The team verified that OSPF neighborship in Area 0 is established between RX and R2 Which action must be taken to choose the shortest path and resolve the issue? A) B) C) D)

Refer to the exhibit. Refer to the exhibit There is a BGP traffic path issue between Customer-1 and Customer-2 Users from Customer-2 have reported file transfer issues High utilization on the path between both customers causes many packet drops. Which configuration resolves the issue?

Question 72 - 300-510 discussion

Report

A network engineer is troubleshooting OSPF multiare a. Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?

A.

hierarchical CLI

B.

routing process enabled by default on all interfaces

C.

DR support for topology management

D.

show lp ospf topology command

Show Answer

asked 07/10/2024

Sebastian van de Zweerde

43 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first