ExamGecko
Search Search Login
Home Home / Cisco / 300-510
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit.
Refer to the exhibit. After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration?
Refer to the exhibit. Refer to the exhibit. Users connected to an application on 1.1.1.1 via routers CE1 and CE2 are complaining of frequent disconnections. While troubleshooting the issue, a network engineer with an employee ID: 4333:96:916 determined that the application itself is working normally, but the link connected to the 1.1.1.1 application is flapping. The users on CE1 and CE2 are accessing applications on 2.2.2.2 without difficulty. Which action resolves the issue?
Refer to the exhibit Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?
Refer to the exhibit. Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)
An ISP has an MPLS VPN-based network with 12 PE routers. How many peerings are required between the 12 routers if the engineer has not configured route reflectors?
Refer to the exhibit. Which LSA type is indicated by this router output?
An engineer is troubleshooting a connectivity issue across the MPLS network and is verifying the forwarding behavior of packets. Which table does the engineer look at to verify the forwarding behavior of an IP packet as it enters the MPLS network at the ingress LSR?
Refer to the exhibit. Refer to the exhibit MPLS traffic from the packet core that is connected to router RX (10 10 101) to the radio network that is connected to router RB (10 10 10 6) uses the longer route RB R2 RY RX RX and R2 are configured with a default value of LDP hello and hold intervals The team verified that OSPF neighborship in Area 0 is established between RX and R2 Which action must be taken to choose the shortest path and resolve the issue? A) B) C) D)
Refer to the exhibit. Refer to the exhibit There is a BGP traffic path issue between Customer-1 and Customer-2 Users from Customer-2 have reported file transfer issues High utilization on the path between both customers causes many packet drops. Which configuration resolves the issue?

Question 97 - 300-510 discussion

Report
Export

Refer io the exhibit.

While applying the configurations on two routers an engineer notices that OSPF adjacency Between them remains down Through the ping test the engineer confirmed that both me routers have Layer 3 reachability between them Which action should me engineer take to make the adjacencies to full?

A.

Enter the command ip ospf authentication in R2 interface

Answers
A.

Enter the command ip ospf authentication in R2 interface

B.

Enable OSPF just inside the router OSPF process not in the interfaces of any router

Answers
B.

Enable OSPF just inside the router OSPF process not in the interfaces of any router

C.

Delete the area 0 authentication message-digest command from the OSPF process in R1

Answers
C.

Delete the area 0 authentication message-digest command from the OSPF process in R1

D.

Delete the area 0 authentication message-digest command from the OSPF process in R2

Answers
D.

Delete the area 0 authentication message-digest command from the OSPF process in R2

Suggested answer: A
Show Answer
asked 07/10/2024
Gilbert Mendoza
38 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms