Home

Home / Cisco / 300-620

Question list

List of questions

Question 1

(0)

An engineer is implementing a Cisco ACI data center network that includes Cisco Nexus 2000 Series 10G fabric extenders. Which physical topology is supported?

Question 2

(0)

An ACI administrator notices a change in the behavior of the fabric. Which action must be taken to determine if a human intervention introduced the change?

Question 3

(0)

An engineer is creating a configuration import policy that must terminate if the imported configuration is incompatible with the existing system. Which import mode achieves this result?

Question 4

(0)

Which components must be configured for the BGP Route Reflector policy to take effect?

Question 5

(0)

Which type of policy configures the suppression of faults that are generated from a port being down?

Question 6

(0)

Which type of profile needs to be created to deploy an access port policy group?

Question 7

(0)

A situation causes a fault to be raised on the APIC. The ACI administrator does not want that fault to be raised because it is not directly relevant to the environment. Which action should the admin

Question 8

(0)

A RADIUS user resolves its role via the Cisco AV Pair. What object does the Cisco AV Pair resolve to?

Question 9

(0)

Which feature dynamically assigns or modifies the EPG association of virtual machines based on their attributes?

Question 10

(0)

Which feature allows firewall ACLs to be configured automatically when new endpoints are attached to an EPG?

Open VPLUS File

Convert VPLUS to PDF

Related questions

A network engineer demonstrates Cisco ACI to a customer. One of the test cases is to validate a disaster recovery event by resetting the ACI fabric to factory and then restoring the fabric to the state it was in before the event. Which setting must be enabled on ACI to export all configuration parameters that are necessary to meet these requirements?

Refer to the exhibit. Refer to the exhibit. An engineer is configuring a production Multi-Site solution to provide connectivity from EPGs from a specific site to networks reachable through a remote site L3OUT. All required schema and template objects are already defined. Which additional configuration must be implemented in the Multi-Site Orchestrator to support the cross-site connectivity?

Refer to the exhibit. Refer to the exhibit. An engineer must divert the traffic between VM-1 and VM-2 by using a Multi- Node service graph. The solution should prevent an insufficient number of available Layer 4 to Layer 7 devices in the first cluster. Which configuration set accomplishes this goal?

An application team tells the Cisco ACI network administrator that it wants to monitor the statistics of the unicast and BUM traffic that are seen in a certain EPG. Which statement describes the collection statistics?

What does a bridge domain represent?

Refer to the exhibit. Refer to the exhibit. Server A is connected to the Cisco ACI fabric using two teamed interfaces. One interface in a team is configured as active and the other remains in standby mode. When a failover occurs and the standby interface becomes active, it uses its built-in MAC address to send traffic. Which bridge domain configuration must be applied to resolve the issue?

What is the advantage of implementing an active-active firewall cluster that is stretched across separate pods when anycast services are configured?

Refer to the exhibit. Which two configurations enable inter-VRF communication? (Choose two.)

Refer to the exhibit. Refer to the exhibit. A Cisco APIC raises an error when the EPG must accept endpoints from a VMM domain created. Which action clears the fault?

When a pre-provision immediacy is used, when is the policy downloaded to the Cisco ACI leaf switch?

Question 189 - 300-620 discussion

Report

What are two PBR characteristics of the Cisco ACI Active-Active Across Pods deployment mode in Cisco ACI Multi-Pod design? (Choose two.)

A.

Traffic is dynamically redirected to the firewall that owns the connection.

B.

Deployment occurs in transparent mode.

C.

The connection state is unsynchronized.

D.

Deployment occurs in go-to mode only.

E.

This mode causes the traffic to flow asymmetrically.

Show Answer

asked 07/10/2024

Maija Janite

38 questions

User

Your answer: A B C D E

0 comments

Sorted by

Leave a comment first