ExamGecko
Search Search Login
Home Home / Cisco / 350-401
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

What are two differences between the RIB and the FIB? (Choose two.)
Which option works with a DHCP server to return at least one WLAN management interface IP address during the discovery phase and is dependent upon the VCI of the AP?
An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?
An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)
An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?
Which port is required to allow APs to join a WLC when directed broadcasts are used on a Cisco iOS switch?
Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?
Refer to the Exhibit. Refer to the exhibit. Which action must be performed to allow RESTCONF access to the device?
Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?
Which configuration allows administrators to configure the device through the console port and use a network authentication server? A) B) C) D)

Question 595 - 350-401 discussion

Report
Export

SIMULATION

Configure HSRP between DISTRO-SW1 and DISTRO-SW2 on VLAN 100 for hosts connected to ACCESSSW1 to achieve these goals:

A.

Configure group number 1 using the virtual IP address of 192.168.1.1/24.

Answers
A.

Configure group number 1 using the virtual IP address of 192.168.1.1/24.

B.

Configure DlSTRO-SW1 as the active router using a priority value of 110 and DISTRO-SW2 as the standby router.

Answers
B.

Configure DlSTRO-SW1 as the active router using a priority value of 110 and DISTRO-SW2 as the standby router.

C.

Ensure that DISTRO-SW2 will take over the active role when DISTRO-SW1 goes down, and when DISTRO-SW1 recovers, it automatically resumes the active role.

DISTRO-SW2

Answers
C.

Ensure that DISTRO-SW2 will take over the active role when DISTRO-SW1 goes down, and when DISTRO-SW1 recovers, it automatically resumes the active role.

DISTRO-SW2

D.

See the solution below in

Answers
D.

See the solution below in

Suggested answer: A

Explanation:

DISTRO-SW1

Explanation:

DISTRO-SW1

Sw1

int vlan 100

standby 1 ip 192.168.1.1

standby 1 priority 110

standby 1 preempt

copy run start

DISTRO-SW2

SW2

int vlan 100

standby 1 ip 192.168.1.1

standby 1 preempt

copy run start

OR

MINOR CHANGE IN ABOVE HSRP SCENERIO

Check the IP address 1.254 check the minimum 15 seconds solution get change.

DISTRO-SW1

Sw1 int vlan 100

glbp 1 ip 192.168.1.254

glbp 1 priority 110

glbp 1 timers 5 15

glbp 1 preempt

copy run start

DISTRO-SW2

SW2

int vlan 100

glbp 1 ip 192.168.1.254

glbp 1 timers 5 15

glbp 1 preempt

copy run start

Show Answer
asked 10/10/2024
So young Jang
27 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms