ExamGecko
Search Search Login
Home Home / Cisco / 350-401
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

What are two differences between the RIB and the FIB? (Choose two.)
Which option works with a DHCP server to return at least one WLAN management interface IP address during the discovery phase and is dependent upon the VCI of the AP?
An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?
An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?
Which port is required to allow APs to join a WLC when directed broadcasts are used on a Cisco iOS switch?
An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)
Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?
Refer to the Exhibit. Refer to the exhibit. Which action must be performed to allow RESTCONF access to the device?
Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?
A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Client connected to the corporate WLAN roam seamlessly between access points on the 5520 and 9800 WLC. After a failure on the primary 5520 WLC, all WLAN services remain functional; however, Client roam between the 5520 and 9800 controllers without dropping their connection. Which feature must be configured to remedy the issue?

Question 616 - 350-401 discussion

Report
Export

Refer to the exhibit.

Which two commands ensure that DSW1 becomes root bridge for VLAN 10? (Choose two)

A.

DSW1(config)#spanning-tree vlan 10 priority 4096 Most Voted

Answers
A.

DSW1(config)#spanning-tree vlan 10 priority 4096 Most Voted

B.

DSW1(config)#spanning-tree vlan 10 priority root

Answers
B.

DSW1(config)#spanning-tree vlan 10 priority root

C.

DSW2(config)#spanning-tree vlan 10 priority 61440 Most Voted

Answers
C.

DSW2(config)#spanning-tree vlan 10 priority 61440 Most Voted

D.

DSW1(config)#spanning-tree vlan 10 port-priority 0

Answers
D.

DSW1(config)#spanning-tree vlan 10 port-priority 0

E.

DSW2(config)#spanning-tree vlan 20 priority 0

Answers
E.

DSW2(config)#spanning-tree vlan 20 priority 0

Suggested answer: C, D

Explanation:

Ref: Scaling Networks v6 Companion Guide

“STP

…

Extended System ID

…

Bridge Priority

The bridge priority is a customizable value that can be used to influence which switch becomes the root bridge. The switch with the lowest priority, which implies the lowest BID, becomes the root bridge because a lower priority value takes precedence.

…

The default priority value for all Cisco switches is the decimal value 32768. The range is 0 to 61440, in increments of 4096. Therefore, valid priority values are 0, 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, and 61440. A bridge priority of 0 takes precedence over all other bridge priorities. All other values are rejected.

Show Answer
asked 10/10/2024
Husein M
34 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms