ExamGecko
Search Search Login
Home Home / Cisco / 350-401
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

What are two differences between the RIB and the FIB? (Choose two.)
Which option works with a DHCP server to return at least one WLAN management interface IP address during the discovery phase and is dependent upon the VCI of the AP?
An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?
An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?
Which port is required to allow APs to join a WLC when directed broadcasts are used on a Cisco iOS switch?
Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?
Refer to the Exhibit. Refer to the exhibit. Which action must be performed to allow RESTCONF access to the device?
An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)
Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?
A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Client connected to the corporate WLAN roam seamlessly between access points on the 5520 and 9800 WLC. After a failure on the primary 5520 WLC, all WLAN services remain functional; however, Client roam between the 5520 and 9800 controllers without dropping their connection. Which feature must be configured to remedy the issue?

Question 653 - 350-401 discussion

Report
Export

Refer to the exhibit.

Company policy restricts VLAN 10 to be allowed only on SW1 and SW2. All other VLANs can be on all three switches. An administrator has noticed that VLAN 10 has propagated to SW3. Which configuration corrects the issue?

A.

SW1(config)#intgi1/1

SW1(config)#switchport trunk allowed vlan 1-9,11-4094

Answers
A.

SW1(config)#intgi1/1

SW1(config)#switchport trunk allowed vlan 1-9,11-4094

B.

SW2(config)#intgi1/2

SW2(config)#switchport trunk allowed vlan 10

Answers
B.

SW2(config)#intgi1/2

SW2(config)#switchport trunk allowed vlan 10

C.

SW2(config)#int gi1/2

SW2(config)#switchport trunk allowed vlan 1-9,11-4094

Answers
C.

SW2(config)#int gi1/2

SW2(config)#switchport trunk allowed vlan 1-9,11-4094

D.

SWl(config)#intgi1/1

SW1(config)#switchport trunk allowed vlan 10

Answers
D.

SWl(config)#intgi1/1

SW1(config)#switchport trunk allowed vlan 10

Suggested answer: C
Show Answer
asked 10/10/2024
Ruud God
36 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms