ExamGecko
Search Search Login
Home Home / Cisco / 350-401
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which option works with a DHCP server to return at least one WLAN management interface IP address during the discovery phase and is dependent upon the VCI of the AP?
What are two differences between the RIB and the FIB? (Choose two.)
An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?
An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?
Which port is required to allow APs to join a WLC when directed broadcasts are used on a Cisco iOS switch?
Refer to the Exhibit. Refer to the exhibit. Which action must be performed to allow RESTCONF access to the device?
An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)
Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?
Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?
A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Client connected to the corporate WLAN roam seamlessly between access points on the 5520 and 9800 WLC. After a failure on the primary 5520 WLC, all WLAN services remain functional; however, Client roam between the 5520 and 9800 controllers without dropping their connection. Which feature must be configured to remedy the issue?

Question 782 - 350-401 discussion

Report
Export

Refer to the exhibit.

Which action must be taken to configure a WLAN for WPA2-AES with PSK and allow only 802.l1r-capable clients to connect?

A.

Change Fast Transition to Adaptive Enabled and enable FT * PSK

Answers
A.

Change Fast Transition to Adaptive Enabled and enable FT * PSK

B.

Enable Fast Transition and FT + PSK.

Answers
B.

Enable Fast Transition and FT + PSK.

C.

Enable Fast Transition and PSK

Answers
C.

Enable Fast Transition and PSK

D.

Enable PSK and FT + PSK.

Answers
D.

Enable PSK and FT + PSK.

Suggested answer: A

Explanation:

This is because Fast Transition (FT) is a feature that allows 802.11r-capable clients to roam faster between access points by reducing the authentication and key exchange time. FT can be configured in two modes: adaptive and over-the-DS. Adaptive mode is recommended for mixed environments where both 802.11r-capable and non-capable clients are present, as it allows the access point to negotiate the FT mode with the client. Over-the-DS mode is only suitable for environments where all clients are 802.11r-capable, as it requires the access point to communicate with the previous access point over the distribution system. FT + PSK is a security option that enables FT with pre-shared key (PSK) authentication, which is a simple and common method of securing wireless networks. WPA2-AES is an encryption standard that provides strong security and privacy for wireless networks. The source of this answer is the Cisco ENCOR v1.1 course, module 7, lesson 7.2: Implementing WPA2 and WPA3.

Show Answer
asked 10/10/2024
Istvan Molnar
33 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms