Home

Home / Cisco / 350-401

Question list

List of questions

Question 1

(0)

What are two benefits of YANG? (Choose two.)

Question 2

(0)

Refer to the exhibit. An engineer must create a configuration that executes the show run command and then terminates the session when user CCNP legs in. Which configuration change is required?

Question 3

(0)

Wireless users report frequent disconnections from the wireless network. While troubleshooting a network engineer finds that after the user a disconnect, the connection re-establishes automatically

Question 4

(0)

Refer to the exhibit. An engineer must modify the access control list EGRESS to allow all IP traffic from subnet 10.1.10.0/24 to 10.1.2.0/24. The access control list is applied in the outbound di

Question 5

(0)

What is used to perform OoS packet classification?

Question 6

(0)

What is the recommended MTU size for a Cisco SD-Access Fabric?

Question 7

(0)

Refer to the exhibit. After configurating an IPsec VPN, an engineer enters the show command to verify the ISAKMP SA status. What does the status show?

Question 8

(0)

Refer to the exhibit. Which configuration allows Customer2 hosts to access the FTP server of Customer1 that has the IP address of 192.168.1.200?

Question 9

(0)

A customer requests a network design that supports these requirements: Which protocol does the design include?

Question 10

(0)

Which two network problems Indicate a need to implement QoS in a campus network? (Choose two.)

Open VPLUS File

Convert VPLUS to PDF

Related questions

What are two differences between the RIB and the FIB? (Choose two.)

Which option works with a DHCP server to return at least one WLAN management interface IP address during the discovery phase and is dependent upon the VCI of the AP?

An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?

An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?

Which port is required to allow APs to join a WLC when directed broadcasts are used on a Cisco iOS switch?

Refer to the Exhibit. Refer to the exhibit. Which action must be performed to allow RESTCONF access to the device?

Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?

Refer to the Exhibit. Refer to the exhibit An engineer is troubleshooting an mDNS issue in an environment where Cisco ISE is used to dynamically assign mDNS roles to users The engineer has confirmed that ISE is sending the correct values, but name resolution is not functioning as expected Which WLC configuration change resolves the issue?

A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Client connected to the corporate WLAN roam seamlessly between access points on the 5520 and 9800 WLC. After a failure on the primary 5520 WLC, all WLAN services remain functional; however, Client roam between the 5520 and 9800 controllers without dropping their connection. Which feature must be configured to remedy the issue?

Which configuration allows administrators to configure the device through the console port and use a network authentication server? A) B) C) D)

Question 937 - 350-401 discussion

Report

Refer to the exhibit.

Which command required to validate that an IP SLA configuration matches the traffic between the branch office and the central site?

A.

R1# show ip sla configuration

B.

R1# show Ip sla group schedule

C.

R1# show Ip route

D.

R1# show ip sla statistics

Show Answer

asked 10/10/2024

Rafal Wozniak

37 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first