ExamGecko
Search Search Login
Home Home / Cisco / 350-601
Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. An engineer configures FCoE in a newly installed data center. Which configuration must be applied to activate VSAN 100 on VFC100?
Refer to the exhibit. A source is sending a multicast traffic stream to the receiver. How is the multicast traffic expected to flow through the network when it reaches a vPC peer?
Refer to the exhibit. An engineer must access a Cisco UCS C-Series server KVM from a remote location. The engineer must use the out-of-band interface to access the KYM. Which configuration set meets these requirements?
Refer to the exhibit. Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal? A) B) C) D)
DRAG DROP Refer to the exhibit. During a recent outage, a network engineer discovered that host A started to experience intermittent connectivity, when Leaf102 was down. Drag and drop the code snippets from the bottom onto the boxes in the code to resolve the problem. Not all code snippets are used.
Refer to the exhibit. Refer to the exhibit. What is the result of executing this python code?
What are two types of FC/FCoE oversubscription ratios? (Choose two.)
Refer to the exhibit. A network engineer must configure the physical domain and attach a VLAN pool to it. Which two commands accomplish this goal? (Choose two.)
Refer to the exhibit. A network engineer configures the VXLAN between the routers in a data center. The VLAN 10 must be extended between routers A and B. The initial VXLAN configuration is completed on RouterA. Which configuration finishes the VXLAN configuration on Router A? A. B. C. D.
DRAG DROP An engineer deploys a custom guest shell rootfs onto multiple switches. Drag and drop the steps from the left into the correct order on the right. Export the Guest Shell rootfs.

Question 170 - 350-601 discussion

Report
Export

Refer to the exhibit.

Which configuration ensure that the cisco Nexus 7000 series switches are the primary devices for LACP?

A.

N7K_A(config-vpc-domain)# role priority 1 N7K_B(config-vpc-domain )# role priority 2

Answers
A.

N7K_A(config-vpc-domain)# role priority 1 N7K_B(config-vpc-domain )# role priority 2

B.

N7K_A(config-vpc-domain)# system-priority 32768 N7K_B(config-vpc-domain)# system-priority 32768

Answers
B.

N7K_A(config-vpc-domain)# system-priority 32768 N7K_B(config-vpc-domain)# system-priority 32768

C.

N7K_A(config-vpc-domain)# system-priority 100 N7K_B(config-vpc-domain)# system-priority 200

Answers
C.

N7K_A(config-vpc-domain)# system-priority 100 N7K_B(config-vpc-domain)# system-priority 200

D.

N7K_A(config-vpc-domain)# system-priority 4000 N7K_B(config-vpc-domain)# system-priority 4000

Answers
D.

N7K_A(config-vpc-domain)# system-priority 4000 N7K_B(config-vpc-domain)# system-priority 4000

Suggested answer: C

Explanation:

To ensure that the Cisco Nexus 7000 series switches are the primary devices for LACP, the system priority needs to be configured with lower values indicating higher priority. In this case, setting N7K_A with a system priority of 100 and N7K_B with a system priority of 200 ensures that N7K_A has a higher priority and becomes the primary device for LACP. The system priority is used in the LACP system ID which determines the LACP priority; the lower the value, the higher the priority.

Show Answer
asked 10/10/2024
Arnaldo Martinez 2-30793
42 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms