Home

Home / Cisco / 350-601

Question list

List of questions

Question 1

(0)

An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements: * Establish adjacency to the remote peer by using multicast. * Enable

Question 2

(0)

An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image. What is expected to occur in this case?

Question 3

(0)

Which configuration statically assigns VSAN membership to a virtual Fibre Channel interface?

Question 4

(0)

An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth 1/2 interface for both switches must be advertised via OSPF. However, these interfaces must not

Question 5

(0)

An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before impor

Question 6

(0)

An engineer must configure HTTPS secure management for Cisco UCS Manager using a key ring named kr2016 and a key size of 1024 bits. The environment consists of a primary fabric interconnect named UC

Question 7

(0)

Which server policy is used to install new Cisco IMC software on a server?

Question 8

(0)

A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between th

Question 9

(0)

Refer to the exhibit. An engineer is configuring a VSAN on the network Which option must be selected to create the VSAN?

Question 10

(0)

A customer wants to offload some of its order processing to a public cloud environment. The customer environment is based on Cisco ACI and uses Puppet with containenzed applications. The operations

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibit. An engineer configures FCoE in a newly installed data center. Which configuration must be applied to activate VSAN 100 on VFC100?

Refer to the exhibit. A source is sending a multicast traffic stream to the receiver. How is the multicast traffic expected to flow through the network when it reaches a vPC peer?

Refer to the exhibit. Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal? A) B) C) D)

DRAG DROP Refer to the exhibit. During a recent outage, a network engineer discovered that host A started to experience intermittent connectivity, when Leaf102 was down. Drag and drop the code snippets from the bottom onto the boxes in the code to resolve the problem. Not all code snippets are used.

Refer to the exhibit. An engineer must access a Cisco UCS C-Series server KVM from a remote location. The engineer must use the out-of-band interface to access the KYM. Which configuration set meets these requirements?

Refer to the exhibit. Refer to the exhibit. What is the result of executing this python code?

What are two types of FC/FCoE oversubscription ratios? (Choose two.)

DRAG DROP An engineer deploys a custom guest shell rootfs onto multiple switches. Drag and drop the steps from the left into the correct order on the right. Export the Guest Shell rootfs.

An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect. Which backup type must be selected to meet these requirements?

An engineer must perform a backup and restore in Cisco UCS to rebuild the system in a disaster recovery scenario. The backup file must be encrypted to prevent the passwords from being stored as clear text. Which backup configuration meets these requirements?

Question 416 - 350-601 discussion

Report

An engineer troubleshoots an Fibre Channel deployment on a Cisco MDS 9000 Series Switch. What does this output indicate about port channel 1?

A.

Port channel 1 is configured to be an ISL.

B.

Port channel 1 is configured to connect to a host bus adapter.

C.

Port channel 1 is configured to connect to an NPIV switch.

D.

Port channel 1 is configured to connect to an NPV switch.

Show Answer

asked 10/10/2024

Swapnil Salunke

39 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first