ExamGecko
Search Search Login
Home Home / Cisco / 350-701
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which compliance status is shown when a configured posture policy requirement is not met?
An engineer is configuring device-hardening on a router in order to prevent credentials from being seen if the router configuration was compromised. Which command should be used?
Which two features are used to configure Cisco ESA with a multilayer approach to fight viruses and malware? (Choose two)
Which two application layer preprocessors are used by Firepower Next Generation Intrusion Prevention System? (Choose two)
Which Cisco platform onboards the endpoint and can issue a CA signed certificate while also automatically configuring endpoint network settings to use the signed endpoint certificate, allowing the endpoint to gain network access?
An engineer wants to generate NetFlow records on traffic traversing the Cisco ASA. Which Cisco ASA command must be used?
DRAG DROP Drag and drop the capabilities of Cisco Firepower versus Cisco AMP from the left into the appropriate category on the right.
What is a characteristic of Firepower NGIPS inline deployment mode?
Which ASA deployment mode can provide separation of management on a shared appliance?
Which PKI enrollment method allows the user to separate authentication and enrollment actions and also provides an option to specify HTTP/TFTP commands to perform file retrieval from the server?

Question 369 - 350-701 discussion

Report
Export

Refer to the exhibit.


All servers are in the same VLAN/Subnet. DNS Server-1 and DNS Server-2 must communicate with each other, and communicate with default gateway multilayer switch. Which type of private VLAN ports should be configured to prevent communication and the file server?

A.

Configure GigabitEthernet0/1 as community port, GigabitEthernet0/2 as promiscuous port, GigabitEthernet0/3 and GigabrtEthernet0/4 as isolated ports

Answers
A.

Configure GigabitEthernet0/1 as community port, GigabitEthernet0/2 as promiscuous port, GigabitEthernet0/3 and GigabrtEthernet0/4 as isolated ports

B.

Configure GigabitEthernet0/1 as community port, GigabitEthernet0/2 as isolated port, and GigabitEthernet0/3 and GigabitEthernet0/4 as promiscuous ports

Answers
B.

Configure GigabitEthernet0/1 as community port, GigabitEthernet0/2 as isolated port, and GigabitEthernet0/3 and GigabitEthernet0/4 as promiscuous ports

C.

Configure GigabitEthernet0/1 as promiscuous port, GigabitEthernet0/2 as community port, and GigabitEthernet0/3 and GigabitEthernet0/4 as isolated ports

Answers
C.

Configure GigabitEthernet0/1 as promiscuous port, GigabitEthernet0/2 as community port, and GigabitEthernet0/3 and GigabitEthernet0/4 as isolated ports

D.

Configure GigabitEthernet0/1 as promiscuous port, GigabitEthernet0/2 as isolated port, and GigabitEthernet0/3 and GigabitEthernet0/4 as community ports

Answers
D.

Configure GigabitEthernet0/1 as promiscuous port, GigabitEthernet0/2 as isolated port, and GigabitEthernet0/3 and GigabitEthernet0/4 as community ports

Suggested answer: D
Show Answer
asked 10/10/2024
Ivan Mazala
43 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms