ExamGecko
Search Search Login
Home Home / HP / HPE7-A01
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which component is used by the Aruba Network Analytics Engine (NAE)?
Which standard supported by some Aruba APs can enable a customer to accurately locate wireless client devices within a few meters?
Your customer currently has Iwo (2) 5406 modular switches with MSTP configured as their core switches. You are proposing a new solution. What would you explain regarding the Aruba CX VSX switch pair when the Primary VSX node is replaced and the system MAC is replaced?
For an Aruba AOS10 AP in mixed mode, which factors can be used to determine the forwarding role assigned to a client? (Select two.)
For the Aruba CX 6400 switch, what does virtual output queueing (VOQ) implement that is different from most typical campus switches?
You need to drop excessive broadcast traffic on an ingress port or an ArubaOS-CX switch. What is the best feature to use for this task?
A customer just upgraded aggregation layer switches and noticed traffic dropping for 120 seconds after the aggregation layer came online again. What is the best way to avoid having this traffic dropped given the topology below?
You are doing tests in your lab and with the following equipment specifications: * AP1 has a radio that generates a 20 dBm signal * AP2 has a radio that generates a 8 dBm signal * AP1 has an antenna with a gain of 7 dBI. * AP2 has an antenna with a gain of 12 dBI. * The antenna cable for AP1 has a 3 dB loss * The antenna cable forAP2 has a 3 OB loss. What would be the calculated Equivalent Isotropic Radiated Power (EIRP) for AP1?
When configuring UBT on a switch what will happen when a gateway role is not specified?
Which statements regarding 0SPFv2 route redistribution are true for Aruba OS CX switches? (Select two.)

Question 84 - HPE7-A01 discussion

Report
Export

With the Aruba CX 6000 24G switch with uplinks of 1/1/25 and what does the switch do when a client port detects a loop and the do-not-disabie parameter is used?

A.
Port status will be validated once status is cleared
Answers
A.
Port status will be validated once status is cleared
B.
An event log message is created.
Answers
B.
An event log message is created.
C.
The network analytics engine is triggered.
Answers
C.
The network analytics engine is triggered.
D.
Port status led blinks in amber with 100hz.
Answers
D.
Port status led blinks in amber with 100hz.
Suggested answer: B

Explanation:

The correct answer is B. An event log message is created.

The do-not-disable parameter is used to prevent the switch from disabling the port when a loop is detected by the loop-protect feature. Instead, the switch will generate an event log message that indicates the port number and the VLAN ID where the loop was detected. The switch will also send a trap to the SNMP manager, if configured1.

The other options are incorrect because:

A) Port status will not be validated once status is cleared. The port will remain enabled even if a loop is detected, unless the loop-protect action is changed to tx-disable or tx-rx-disable1.

C) The network analytics engine will not be triggered by a loop detection. The network analytics engine is a feature that allows users to monitor and troubleshoot network issues using scripts and agents2.

D) Port status LED will not blink in amber with 100Hz. The port status LED will indicate the normal port status, such as link speed and activity, regardless of the loop detection3.

Show Answer
asked 16/09/2024
Ronald Armas
34 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms