ExamGecko
Search Search Login
Home Home / Juniper / JN0-351
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Exhibit. You are using OSPF to advertise the subnets that are used by the Denver and Dallas offices. The routers that are directly connected to the Dallas and Denver subnets are not advertising the connected subnets. Referring to the exhibit, which two statements are correct? (Choose two.)
What is the default keepalive time for BGP?
Which statement about aggregate routes is correct?
In RSTP, which three port roles are associated with the discarding state? (Choose three.)
Exhibit. You want to verify prefix information being sent from 10.36.1.4. Which two statements are correct about the output shown in the exhibit? (Choose two.)
Exhibit. The ispi _ inet. 0 route table has currently no routes in it. What will happen when you commit the configuration shown on the exhibit?
Exhibit Which command displays the output shown in the exhibit?
An update to your organization's network security requirements document requires management traffic to be isolated in a non-default routing-instance. You want to implement this requirement on your Junos-based devices. Which two commands enable this behavior? (Choose two.)
You have DHCP snooping enabled but no entries are automatically created in the snooping database for an interface on your EX Series switch. What are two reasons for the problem? (Choose two.)
You are a network operator who wants to add a second ISP connection and remove the default route to the existing ISP You decide to deploy the BGP protocol in the network. What two statements are correct in this scenario? (Choose two.)

Question 64 - JN0-351 discussion

Report
Export

Exhibit

Referring to the exhibit, which two configuration changes must you apply for packets to reach from R1 to R3 using IS-IS? (Choose two.)

A.
On R1, enable Level 1 on the ge-0/0/1 interface.
Answers
A.
On R1, enable Level 1 on the ge-0/0/1 interface.
B.
On R3 disable Level 2 on the ge-0/0/4 interface.
Answers
B.
On R3 disable Level 2 on the ge-0/0/4 interface.
C.
On R1, disable Level 2 on the ge-0/0/1 interface.
Answers
C.
On R1, disable Level 2 on the ge-0/0/1 interface.
D.
On R3 enable Level 1 on the ge-0/0/4 interface
Answers
D.
On R3 enable Level 1 on the ge-0/0/4 interface
Suggested answer: A, D

Explanation:

A) On R1, enable Level 1 on the ge-0/0/1 interface.In IS-IS, both levels (Level 1 and Level 2) are enabled by default when you enable IS-IS on an interface1.Level 1 systems route within an area2.If the destination is outside an area, Level 1 systems route toward a Level 2 system2. Therefore, enabling Level 1 on the ge-0/0/1 interface on R1 would allow packets to reach from R1 to R3.

D) On R3 enable Level 1 on the ge-0/0/4 interfaceSimilarly, enabling Level 1 on the ge-0/0/4 interface on R3 would allow packets to reach from R1 to R3.

These explanations are based on the IS-IS configuration documents and learning resources available at Juniper Networks1and Cisco34.

Show Answer
asked 18/09/2024
Oren Dahan
45 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms