Home

Home / Juniper / JN0-682

Question list

List of questions

Question 1

(0)

Which statement is true about the route shown in the exhibit?

Question 2

(0)

You are asked to implement VXLAN in your data center network. You must choose between implementing EVPN signaling and multicast signaling. Which two statements are correct in this scenario? (Choose

Question 3

(0)

You have a two spine and four leaf CRB topology and you must ensure that the hosts connected to the leaf devices have reachability to all IRB interface addresses, including the local spine IRB addr

Question 4

(0)

You want to configure redundant Layer 3 gateways In this scenario, which two juniper best practices would accomplish this task? (Choose two.)

Question 5

(0)

You are asked to configure VXLAN for you c data center using multicast to exchange VTEP information? In this scenario, which two configuration parameters must match on the VTEPs in the same VXLAN s

Question 6

(0)

A client with five data centers spread around the country uses MPLS L2VPNs to provides point- to- point data center interconnect between each data center in a full-mesh network. The client Is consid

Question 7

(0)

Which EVPN router type prevents BUM traffic from looping back to a multihued host?

Question 8

(0)

You have a site with thousands of MAC addresses multihomed to two leaf nodes in an EVPN VXLAN. In this scenario, which EVPN feature provides fast network convergence in the event of a leaf node link

Question 9

(0)

Which two statements define the use of route targets and route distinguishers in an EVPN? (Choose two.)

Question 10

(0)

You are configuring an EVPN overlay network. You want to ensure that leaf devices can respond to ARP requests from locally connected hosts, when the leaf device knows the MAC of the intended destina

Open VPLUS File

Convert VPLUS to PDF

Related questions

You are troubleshooting an L3VPN that is part of an EVPN/MPLS DCI. You notice that the EVPN overlay BGP session toward 10.29.50.4 is unable to establish. Why is the BGP session failing to establish?

Refer to the exhibit. Referring to the exhibit, which two statements are correct? (Choose two.)

Which two statements about a DHCP relay in an EVPN-VXLAN fabric are correct? (Choose two.)

Which two statements are true Virtual Chassis? (Choose two.)

Which two combinations are supported when configuring a Virtual Chassis Fabric? (Choose two.)

Which protocol is used between VCF member devices to create a loop-free topology?

Referring to the exhibit, each node in the IP fabric is peering to its directly attached neighbor using EBGP. Each node is peering using physical interface IP addresses. Leaf 2 and Leaf 3 are advertising the 10.1.1/24 network into EBGP. Spine 2 must be configured so that it can load- share traffic destined to the 10 1.1/24 network over both next-hop A and next-hop B. Which two actions must be performed to accomplish this task? (Choose two.)

You are asked to enable plug-and-play line card switches in an active VCF without making any future Junos configuration charges. You are also required to ensure that all new line card are automatically upgrade to the correct Junos version without any manual intervention. In this scenario, which two actions will accomplish this task? (Choose two.)

You work in a data center where VMs and hosts are frequently moved. Your design needs to eliminate inefficient traffic flows. In this scenario, which two solutions will satisfy this requirement? (Choose two.)

Which two statements are correct about VXLANs? (Choose two.)

Question 52 - JN0-682 discussion

Report

You choose the EBGP design shown in the exhibit as your IP fabric design. You must ensure that both routes received by the spine nodes will be used for ECMP forwarding.

Which BGP parameter would need to be added to the EBGP configuration of the spine nodes to achieve this goal?

A.

multipath

B.

multihop

C.

add-path

D.

multipath multiple-as

Show Answer

asked 18/09/2024

DATA DYNAMICAL SOLUTIONS

35 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first