Home

Home / Network Appliance / NS0-520

Question list

List of questions

Question 1

(0)

You are asked to serve iSCSI LUNs in an existing SVM on your AFF A220 using ONTAP 9.5. You verified that the iSCSI license is configured on your cluster and that the iSCSI protocol is enabled. Re

Question 2

(0)

You are testing iSCSI LUN failover across a 4-node FAS9000 fabric-attached MetroCluster configuration. In this scenario, which front end configuration is required for non-disruptive host LUN failov

Question 3

(0)

Referring to the exhibit, which two pairs of ports are currently configurable as FC SAN LIFs? (Choose two.)

Question 4

(0)

You have a 4-node cluster with an AFF A300 HA pair and a FAS8200 HA pair. You plan on using the default storage efficiency settings. With inline data compaction, you estimate that you can save 6% of

Question 5

(0)

You have a requirement to serve LUNs with under 200 microsecond latency using local server lass memory. You also are required to use a shared SAN. Using MAX Data as shown in the exhibit, which tw

Question 6

(0)

A company has 20 ESX hosts. Ten of the hosts are connected using FC, and the rest are connected over iSCSI. The FC host HBA queue depth is set to 32, and the iSCSI LUN queue depth is set to 64. The

Question 7

(0)

You want to ensure maximum performance of iSCSI LUNs on an AFF A220. In this scenario, which two actions will accomplish this task? (Choose two.)

Question 8

(0)

You are provisioning storage to an ESX host that uses iSCSI. According to NetApp best practice, which three actions accomplish this task? (Choose three.)

Question 9

(0)

A customer has an AFF A700 connected to a Cisco switch and has verified connectivity but cannot see any LUNs. The customer issued the run -node scaling-01 -command fcp topology show command to ver

Question 10

(0)

A customer is using both FC and NVMe in a cluster. The customer needs to do some work on AFF_1. Referring to the exhibit, what will happen?

Open VPLUS File

Convert VPLUS to PDF

Related questions

An administrator reviews the Upgrade Advisor before performing an upgrade of their ONTAP cluster. What information is detailed in the report? (Choose two.)

A customer wants to deploy NVMe/FC along with an existing FC SAN fabric using ONTAP 9.8. In this scenario, which two actions are correct? (choose two)

Referring to the exhibit, which WWPN would safely be removed from the zone?

You are configuring a 4-node AFF A400 ONTAP 9.8 cluster. The data center switches have limited ports, and you are given one 10-Gigabit Ethernet port per node for external access. In this scenario, which three protocols share the same physical port? (Choose three)

A company wants to use jumbo frames in their Ethernet network. They should set the packet size to which industry conventional value?

Exhibit. You need to configure the SnapCenter Plug-in for VMware vSphere to back up and restore VMware datastores. Referring to the exhibit, which additional LIF type should you create before you configure the plugin?

Referring to the exhibit, which two LIFs would be optimized paths to LUN /vol/OraDev_Vol/OraDev? (Choose two.)

Your customer asks you how to connect a host for SAN access to the newly installed AFF A400 system. In this scenario, which two statements are correct? (choose two)

You upgraded your Linux hosts to SUSE Enterprise Linux 15. In this scenario, which two actions should you perform before you test asymmetric namespace access (ANA)? (Choose two)

An administrator is configuring their existing Ethernet network switches to provide ISCSI LUNs to several servers. The network switches are also used for other traffic from various hosts. In this scenario, which statement is true?

Question 121 - NS0-520 discussion

Report

You are setting up FC ports and must configure the speeds for both the SAN and the host ports. In this scenario, which statement is correct?

A.

Set the target port speed higher than the switch port speed.

B.

Set the target port speed to auto-negotiation.

C.

Set the target port speed to match the switch port speed.

D.

Set the target port speed lower than the switch port speed.

Show Answer

asked 23/09/2024

Arpita Pattnayak

50 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first