Home / Nutanix / NCP-MCI-6.5

Question list

List of questions

Question 1

(0)

HOTSPOT An administrator needs to shut down an AHV cluster to relocate hardware. The administrator upgrades NCC and runs health checks. Which steps should the administrator perform next? Item ins

Question 2

(0)

Which method can be used to migrate a VM configured for UEFI-boot from a Nutanix Hyper-V cluster to AHV?

Question 3

(0)

An administrator needs to report on any alerts generated by a Nutanix cluster that affected the cluster's availability over the past 10 days. Which method should be used to locate these events?

Question 4

(0)

CPU utilization climbs above 90% on several VMs. This causes performance degradation for a business-critical application. How can alerts be configured to notify the administrator before VM CPU util

Question 5

(0)

In Files, how many FSVMs are deployed by default?

Question 6

(0)

A two-node ROBO cluster is configured with a witness VM. What happens when Node A goes down?

Question 7

(0)

How will an HDD failure affect VMs with data on the failed device?

Question 8

(0)

A guest VM should be able to tolerate simultaneous failure of two nodes or drives. What are the minimum requirements for the Nutanix cluster?

Question 9

(0)

HOTSPOT Async DR is configured between two sites. A network outage occurs at the primary site. Which steps must the administrator perform to bring the VMs back into service at the backup site? It

Question 10

(0)

Refer to the exhibit. An administrator is trying to implement the solution that is shown in the exhibit, but has been unsuccessful. Based on the diagram, what is causing the issue?

Related questions

Refer to the exhibit. An administrator is trying to implement the solution that is shown in the exhibit, but has been unsuccessful. Based on the diagram, what is causing the issue?

Which algorithm do snapshots and clones leverage to maximize efficiency and effectiveness?

Which scenario would benefit most from Erasure Coding being enabled on a container?

Refer to Exhibit: An administrator is attempting to create an additional virtual switch on a newly deployed AHV cluster, using the two currently disconnected interfaces. The administrator is unable to select the disconnected interfaces when creating the virtual switch. What is the likely cause of this issue?

A Nutanix cluster is equipped with four nodes. Four VMs on this cluster have been configured with a VM-VM anti-affinity policy and are each being hosted by a different node. What occurs to the cluster and these VMs during an AHV upgrade?

Which two methods are available when migrating a VM from a legacy 3-tier solution using VMware ESXi to AHV? (Choose two.)

An administrator has been alerted to a VM that has high I/O latency and wants to determine if there are any other factors, such as insufficient network or memory resources that correlate, as part of a troubleshooting process. Which type of chart should the administrator create to allow all relevant data to be easily exported to CSV for later analysis?

An administrator is implementing a VDI solution. The workload will be a series of persistent desktops in a dedicated storage container within a four-node cluster Storage optimizations should be set on the dedicated storage container to give optimal performance including during a node failure event Which storage optimizations should the administrator set to meet the requirements?

An administrator is commissioning a Nutanix Enterprise Cloud. Once the user VMs have been deployed and are running, the administrator finds that VMs on the same host are able to communicate, but are unable to communicate between hosts. What must be changed to enable full inter-VM communications?

Microsegmentation was recently enabled in a Nutanix environment. The administrator wants to leverage Prism Central to create a policy that will block all traffic regardless of direction, between two groups of VMs identified by their category. Which policy should be used to meet this requirement?

Question 11 - NCP-MCI-6.5 discussion

The administrator recently had a node fail in an AHV Nutanix cluster. All of the VMs restarted on other nodes in the cluster, but they discovered that the VMs that make up a SQL cluster were running on the failed host. The administrator has been asked to take measures to prevent a SQL outage in the future.

What affinity option will prevent the SQL VMs from running on the same hos?