ExamGecko
Search Search Login
Home Home / Nutanix / NCP-MCI-6.5
Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. An administrator is trying to implement the solution that is shown in the exhibit, but has been unsuccessful. Based on the diagram, what is causing the issue?
Which algorithm do snapshots and clones leverage to maximize efficiency and effectiveness?
Which scenario would benefit most from Erasure Coding being enabled on a container?
Refer to Exhibit: An administrator is attempting to create an additional virtual switch on a newly deployed AHV cluster, using the two currently disconnected interfaces. The administrator is unable to select the disconnected interfaces when creating the virtual switch. What is the likely cause of this issue?
A Nutanix cluster is equipped with four nodes. Four VMs on this cluster have been configured with a VM-VM anti-affinity policy and are each being hosted by a different node. What occurs to the cluster and these VMs during an AHV upgrade?
Which two methods are available when migrating a VM from a legacy 3-tier solution using VMware ESXi to AHV? (Choose two.)
An administrator has been alerted to a VM that has high I/O latency and wants to determine if there are any other factors, such as insufficient network or memory resources that correlate, as part of a troubleshooting process. Which type of chart should the administrator create to allow all relevant data to be easily exported to CSV for later analysis?
An administrator is implementing a VDI solution. The workload will be a series of persistent desktops in a dedicated storage container within a four-node cluster Storage optimizations should be set on the dedicated storage container to give optimal performance including during a node failure event Which storage optimizations should the administrator set to meet the requirements?
An administrator is commissioning a Nutanix Enterprise Cloud. Once the user VMs have been deployed and are running, the administrator finds that VMs on the same host are able to communicate, but are unable to communicate between hosts. What must be changed to enable full inter-VM communications?
Microsegmentation was recently enabled in a Nutanix environment. The administrator wants to leverage Prism Central to create a policy that will block all traffic regardless of direction, between two groups of VMs identified by their category. Which policy should be used to meet this requirement?

Question 176 - NCP-MCI-6.5 discussion

Report
Export

An administrator initially performed a cluster Foundation using a flat switch without any VLAN configuration. After the Foundation, the administrator moved the dual 25Gb data ports and single 1Gb IPMI port to the actual switches with the below network configurations:

. All VLANs are tagged

. VLAN 1000 for CVM\Hypervisor traffic

. VLAN 1001 for User VM traffic

. VLAN 100 for IPMI traffic

After moving the IPMI network links, the administrator can no longer ping the IPMI IPs.

Which two changes does the administrator need to make? (Choose two.)

A.
SSH to AHV and set the VLAN ID using IPMI Tool.
Answers
A.
SSH to AHV and set the VLAN ID using IPMI Tool.
B.
SSH to CVM and restart network services on all host.
Answers
B.
SSH to CVM and restart network services on all host.
C.
SSH to AHV and change the IP address using IPMI tool.
Answers
C.
SSH to AHV and change the IP address using IPMI tool.
D.
SSH to CVM and restart Genesis on all CVMs.
Answers
D.
SSH to CVM and restart Genesis on all CVMs.
Suggested answer: A, C

Explanation:

The issue described pertains to the inability to ping the IPMI IPs after moving the IPMI network links to the actual switches with specific VLAN configurations. The two changes that the administrator needs to make are:

A . SSH to AHV and set the VLAN ID using IPMI Tool: Since all VLANs are tagged in the new network configuration, the IPMI network interface needs to be aware of the VLAN it's supposed to communicate on. This can be achieved by setting the VLAN ID using the IPMI Tool on the AHV.

C . SSH to AHV and change the IP address using IPMI tool: If the IPMI IP addresses were initially set in a different subnet that is not routable in the new network configuration, the administrator would need to change the IPMI IP addresses to match the new network configuration. This can be done by SSHing to the AHV and using the IPMI Tool to change the IP address.

Show Answer
asked 23/09/2024
SIDDIQI TARMIM
38 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms