Home

Home / Cisco / 300-425

Question list

List of questions

Question 1

(0)

A network engineer is working on a design for a wireless network that must support data, voice, and location services. To support these services, which access point placement must the engineer use?

Question 2

(0)

Refer to the exhibit. Which two statements about Cisco Prime Infrastructure are true? (Choose two.)

Question 3

(0)

A customer has noticed that Client Band Select is enabled and no clients are utilizing the 5 GHz band. Which three parameters must be met to ensure that wireless clients use the 5 GHz band? (Choose

Question 4

(0)

How are mobility groups created, excluding mobility anchors?

Question 5

(0)

How should the concept of mobility domains and mobility groups be explained to a customer?

Question 6

(0)

A medium-sized hospitality company with 50 hotels needs to upgrade the existing WLAN in each hotel to 802.11n. During the site surveys for each hotel, what needs to be taken into consideration when

Question 7

(0)

An engineer is using a Cisco AIR-2702i AP to conduct a Layer 1 site Survey, which mode is selected for the AP to discover non-Wi-Fi interference with metageek chanalyzer?

Question 8

(0)

A network engineer needs to create a wireless design to bridge wired IP surveillance cameras in the parking lot through a mesh AP. To which operate mode of the AP should the cameras connect?

Question 9

(0)

A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)

Question 10

(0)

Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)

Open VPLUS File

Convert VPLUS to PDF

Related questions

An engineer in a branch office that does not have a wired backhaul must ensure that local clients can be switched locally and authenticated centrally. In which mode must the AP be configured?

An engineer must design and configure a wireless network for: * pervasive coverage in an oil terminal * casual web and email traffic * 5 GHz What is the best design?

A wireless engineer must assess constraints for a future WLAN deployment for a site that consists of oce cubicles. Which signal propagation attenuation result is associated with this environment?

An engineer is using a Cisco AIR-2702i AP to conduct a Layer 1 site Survey, which mode is selected for the AP to discover non-Wi-Fi interference with metageek chanalyzer?

A customer has noticed that Client Band Select is enabled and no clients are utilizing the 5 GHz band. Which three parameters must be met to ensure that wireless clients use the 5 GHz band? (Choose three.)

A network engineer is retorting an existing building wired with Category 5e with Cisco Aironet 3800 Series APs and mGig switches. Which cable length allows for 5G operation?

A 60,000-square foot outdoor area must be surveyed. The survey must be completed in the least amount of time. Which tool or equipment is used when performing the site survey?

An engineer is designing a network deployment for a technology company. The company has four buildings with access points that must provide seamless wireless coverage and client roaming. The customer data center must have two WLCs and the core switches for the network. Which type of wireless architecture must be used?

A customer Wi-Fi deployment is experiencing the sticky client problem and must enable the optimized roaming feature. The wireless clients have valid security credentials for an SSID and can see an AP that offers that SSID to join. What must be configured to enhance roaming?

Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)

Question 183 - 300-425 discussion

Report

An engineer must optimize client roaming after noticing that clients in the environment are not roaming as expected. Upon reviewing an over- the-air packet capture, the engineer sees that the AP is sending a BSS Transition Management query to the client, which causes it to roam.

The disassociation imminent feature is not enabled on the WLAN. What is the cause of the issue?

A.

Low RSSI check is enabled.

B.

Fast Transition is disabled.

C.

Band Select is enabled.

D.

Optimized roaming is enabled.

Show Answer

asked 07/10/2024

Bright Ngobeni

40 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first