Home

Home / Cisco / 300-815

Question list

List of questions

Question 1

(0)

An administrator is configuring a cluster for ILS and wants to limit the amount of entities that Cisco Unified Communications Manager can write to the database for data that is learned through ILS.

Question 2

(0)

When configuring hunt groups, where do you add the individual directory numbers that will be part of the group?

Question 3

(0)

Refer to the exhibit. The Cisco Unified Border Element receives an INVITE matching inbound dial peer 5002. The outbound dial peer supports only iLBC. and a Local Transcoding Interface is allocate

Question 4

(0)

An IP Telephony administrator is deploying IP phones The administrator has an existing Cisco UCME router with several SCCP & SIP phones registered. The administrator receives a request for a new

Question 5

(0)

An administrator is implementing a new dial-plan on Cisco Unified Border Element. The administrator must ensure that incoming dial-peers are matched based on the IP address from where the incoming r

Question 6

(0)

An engineer must configure call queuing under a Hunt Pilot. After the engineer receives the audio file that will be played to callers during queuing, which two steps should be taken to complete the

Question 7

(0)

Which configuration element of a hunt group allows for changing Calling Party Transformations settings?

Question 8

(0)

Which two types of authentication are supported for the configuration of Intercluster Lookup Service? (Choose two.)

Question 9

(0)

Refer to the exhibit. In an active SIP call between phone user A and phone user B, phone A initiates a call transfer to phone user C. Which two scenarios are correct? (Choose two.)

Question 10

(0)

Refer to the exhibit. Users report that when they dial to Cisco Unity Connection from an external network, they cannot enter any digits. Assuming only in-band DTMF is supported, what is a reason

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibit. An administrator is troubleshooting a problem in which some outbound calls from an internal network to the Internet telephony service provider are not getting connected, but some others connect successfully. The firewall team found that some call attempts on port 5060 came from an unrecognized IP that has not been defined in the firewall rule. What should the administrator configure in the Cisco Unified Border Element to fix this issue?

Which two extended capabilities must be configured on dial peers for fast start-to-early media scenarios (H.323 to SIP interworking)? (Choose two.)

Refer to the exhibit. A collaboration engineer is troubleshooting an issue where the PSTN calls of a Cisco UCM IP phone user are not reaching the PSTN gateway. Which action resolves the issue?

The same digits sent in OOB, as well as in-band on the Cisco Unified Border Element, are being interpreted as duplicate digits by the receiving end. Which configuration must an engineer implement to resolve this issue?

Which section under the Real-Time Monitoring Tool allows for reviewing the call flow and signaling for a SIP call in real time?

Due to a shortage of physical interfaces on a device the administrator requires that a loopback for RTP is used. Which command is required when using a loopback interface for RTP?

An administrator configured Cisco Unified Mobility to block access to remote destinations for certain caller IDs. A user reports that a blocked caller was able to reach a remote destination. Which action resolves the issue?

An administrator is configuring a cluster for ILS and wants to limit the amount of entities that Cisco Unified Communications Manager can write to the database for data that is learned through ILS. Which service parameter is used to adjust this limit?

Cisco UCM has 100,000 entries in the database learned through the ILS Service. Parameter ILS Max Number of Learned Objects in Database value is set to 100,000. What will happen to learned data when the service parameter value is reduced to 50,000?

What are two configureation features of the Client matter code setting in the route pattern configuration? (Choose two.)

Question 49 - 300-815 discussion

Report

Where on Cisco Unified Communications Manager do you configure the standard local route group for a group of devices?

A.

System > Location Info

B.

Call Routing > Route/Hunt > Local Route Group Names

C.

System > Device Pool

D.

Call Routing > Emergency Location > Emergency Location (ELIN) Groups

Show Answer

asked 10/10/2024

Martin GuckÃ½

51 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first