ExamGecko
Search Search Login
Home Home / Cisco / 350-501
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

An engineer is developing a configuration script to enable dial-out telemetry streams using gRPC on several new devices. TLS must be disabled on the devices. Which configuration must the engineer apply on the network?
Which function does RSVP perform in a Cisco MPLS TE environment?
Refer to the exhibit. An engineer working for private Service Provider with employee id: 3948:11:613 is configuring the BGPsec framework. Which two conditions must the engineer take into account? (Choose two.)
Refer to the exhibit. The USER mat is connecting an application on an Internet connection in AS 100 is facing these issues: The USER lost the connection to the application during a failure Between IG and R2. Router R2 configuration a lost due to a power outage. The application the USER is connecting to a hosted behind CE2. What action resolves the issues on R3 and R4 routers?
What is a characteristic of MVPN?
Which statement about TLS is accurate when using RESTCONF to write configurations on network devices'?
Refer to the exhibit. Refer to the exhibit. The operations team for a service provider network is implementing a route map policy. OSPF area 0 should originate the default route with a type 2 metric of 2 when the application server on the connected interface (192.168.1.1) is up. Routers RL and RM have set up OSPF peering with other adjacent routers. Which action meets this requirement?
Refer to the exhibit. Refer to the exhibit. The operations team is implementing an LDP-based configuration in the service-provider core network with these requirements: *RC must establish LDP peering with the loopback IP address as its Router ID *RA must establish LDP peering with RB. RC, and RY. How must the team update the network configuration to successfully enable LDP peering between RA and RC?
Refer to the exhibit. Refer to the exhibit. A network engineer with an employee ID 4379:43:595 is setting up an IS-IS network with these requirements: *Routes with a tag of 80 and IP prefixes other than 192.168.10.20/24 must be redistributed from Level 1 into Level 2. *Route leaking must be configured from Level 2 into the Level 1 domain for routes that are tagged with only 50 or 40. Which configuration must be implemented on RB to meet the requirements?
Refer to the exhibit. A network engineer is implementing an LDP-based MPLS solution to enable packet flow between the two bank sites The engineer was given two requirements * LDP peering must stay up when there is a link failure between R3 and R6 * LDP peering must not flap when there is a link failure between R5 and R6 Which action meets these requirements?

Question 323 - 350-501 discussion

Report
Export

Refer to the exhibit.

Refer to the exhibit. A network administrator implemented MPLS routing between routers R1, R2, R3, and R4. AToM is configured between R1 and R4 to allow Layer 2 traffic from hosts on RA1 and RA2. A targeted MPLS session is established between R1 and R4. Which additional action must the administrator take on all routers so that LDP synchronization occurs between connected LDP sessions?

A.

Disable the MPLS LDP IGP sync holddown.

Answers
A.

Disable the MPLS LDP IGP sync holddown.

B.

Configure OSPF or IS-IS as the routing protocol.

Answers
B.

Configure OSPF or IS-IS as the routing protocol.

C.

Configure EIGRP as the routing protocol using stub areas only.

Answers
C.

Configure EIGRP as the routing protocol using stub areas only.

D.

Enable MPLS LDP sync delay timers.

Answers
D.

Enable MPLS LDP sync delay timers.

Suggested answer: A
Show Answer
asked 10/10/2024
Randy Kana
33 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms