Home

Home / Cisco / 350-501

Question list

List of questions

Question 1

(0)

Egress PE NAT is being used via a single centralized router to provide Internet access to L3VPN customers. Which description of the NAT operation is true?

Question 2

(0)

How much must the MTU be increased when configuring the 802.1q VLAN tag?

Question 3

(0)

Refer to the exhibit: Export statistics received do not include the BGP next hop. Which statement about the NetFlow export statistics is true?

Question 4

(0)

Refer to the exhibit: Which three outcomes occur if the prefix list is added to the neighbor? (Choose three)

Question 5

(0)

Which statement about segment routing prefix segments is true?

Question 6

(0)

You are creating new Cisco MPLS TE tunnels. Which type of RSVP message does the headend router send to reserve bandwidth on the path to the tunnel’s router?

Question 7

(0)

An engineer is setting up overlapping VPNs to allow VRF ABC and XYZ to communicate with VRF CENTRAL but wants to make sure that VRF ABC and XYZ cannot communicate. Which configuration accomplishes t

Question 8

(0)

In an MPLS network, which protocol can be used to distribute a Segment Prefix?

Question 9

(0)

Which statement about Network Services Orchestrator (NSO) is true?

Question 10

(0)

Which task must be performed first to Implement BFD in an IS-IS environment?

Open VPLUS File

Convert VPLUS to PDF

Related questions

An engineer is developing a configuration script to enable dial-out telemetry streams using gRPC on several new devices. TLS must be disabled on the devices. Which configuration must the engineer apply on the network?

Which function does RSVP perform in a Cisco MPLS TE environment?

Refer to the exhibit. An engineer working for private Service Provider with employee id: 3948:11:613 is configuring the BGPsec framework. Which two conditions must the engineer take into account? (Choose two.)

Refer to the exhibit. The USER mat is connecting an application on an Internet connection in AS 100 is facing these issues: The USER lost the connection to the application during a failure Between IG and R2. Router R2 configuration a lost due to a power outage. The application the USER is connecting to a hosted behind CE2. What action resolves the issues on R3 and R4 routers?

What is a characteristic of MVPN?

Which statement about TLS is accurate when using RESTCONF to write configurations on network devices'?

Refer to the exhibit. Refer to the exhibit. The operations team for a service provider network is implementing a route map policy. OSPF area 0 should originate the default route with a type 2 metric of 2 when the application server on the connected interface (192.168.1.1) is up. Routers RL and RM have set up OSPF peering with other adjacent routers. Which action meets this requirement?

Refer to the exhibit. Refer to the exhibit. The operations team is implementing an LDP-based configuration in the service-provider core network with these requirements: *RC must establish LDP peering with the loopback IP address as its Router ID *RA must establish LDP peering with RB. RC, and RY. How must the team update the network configuration to successfully enable LDP peering between RA and RC?

Refer to the exhibit. Refer to the exhibit. A network engineer with an employee ID 4379:43:595 is setting up an IS-IS network with these requirements: *Routes with a tag of 80 and IP prefixes other than 192.168.10.20/24 must be redistributed from Level 1 into Level 2. *Route leaking must be configured from Level 2 into the Level 1 domain for routes that are tagged with only 50 or 40. Which configuration must be implemented on RB to meet the requirements?

Refer to the exhibit. A network engineer is implementing an LDP-based MPLS solution to enable packet flow between the two bank sites The engineer was given two requirements * LDP peering must stay up when there is a link failure between R3 and R6 * LDP peering must not flap when there is a link failure between R5 and R6 Which action meets these requirements?

Question 342 - 350-501 discussion

Report

DRAG DROP

Drag and drop the characteristics from the left onto the automation tool on the right.

Show Answer

asked 10/10/2024

Jimmie Campbell

33 questions

User

0 comments

Sorted by

Leave a comment first