Home

Home / Cisco / 350-601

Question list

List of questions

Question 1

(0)

An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements: * Establish adjacency to the remote peer by using multicast. * Enable

Question 2

(0)

An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image. What is expected to occur in this case?

Question 3

(0)

Which configuration statically assigns VSAN membership to a virtual Fibre Channel interface?

Question 4

(0)

An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth 1/2 interface for both switches must be advertised via OSPF. However, these interfaces must not

Question 5

(0)

An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before impor

Question 6

(0)

An engineer must configure HTTPS secure management for Cisco UCS Manager using a key ring named kr2016 and a key size of 1024 bits. The environment consists of a primary fabric interconnect named UC

Question 7

(0)

Which server policy is used to install new Cisco IMC software on a server?

Question 8

(0)

A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between th

Question 9

(0)

Refer to the exhibit. An engineer is configuring a VSAN on the network Which option must be selected to create the VSAN?

Question 10

(0)

A customer wants to offload some of its order processing to a public cloud environment. The customer environment is based on Cisco ACI and uses Puppet with containenzed applications. The operations

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibit. An engineer configures FCoE in a newly installed data center. Which configuration must be applied to activate VSAN 100 on VFC100?

Refer to the exhibit. A source is sending a multicast traffic stream to the receiver. How is the multicast traffic expected to flow through the network when it reaches a vPC peer?

Refer to the exhibit. An engineer must access a Cisco UCS C-Series server KVM from a remote location. The engineer must use the out-of-band interface to access the KYM. Which configuration set meets these requirements?

Refer to the exhibit. Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal? A) B) C) D)

DRAG DROP Refer to the exhibit. During a recent outage, a network engineer discovered that host A started to experience intermittent connectivity, when Leaf102 was down. Drag and drop the code snippets from the bottom onto the boxes in the code to resolve the problem. Not all code snippets are used.

Refer to the exhibit. Refer to the exhibit. What is the result of executing this python code?

What are two types of FC/FCoE oversubscription ratios? (Choose two.)

Refer to the exhibit. A network engineer must configure the physical domain and attach a VLAN pool to it. Which two commands accomplish this goal? (Choose two.)

An engineer must deploy a Cisco UCS C-Series Server with a single VIC 1455 integrated into a Cisco UCS Manager cluster. Two fiber connections are available, and the deployment has no fabric extenders. Which set of actions accomplishes this goal?

Refer to the exhibit. A network engineer configures the VXLAN between the routers in a data center. The VLAN 10 must be extended between routers A and B. The initial VXLAN configuration is completed on RouterA. Which configuration finishes the VXLAN configuration on Router A? A. B. C. D.

Question 265 - 350-601 discussion

Report

Refer to the exhibit.

Refer to the exhibit. Which action completes the vPC domain implementation?

A.

Allow VLANs on the vPC peer link member interfaces.

B.

Include the VRF management on the vPC domain.

C.

Configure the system MAC on the vPC domain.

D.

Add the vPC member ports to the vPC channel group.

Show Answer

asked 10/10/2024

Claudia Arrais

49 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first