Home

Home / HP / HPE2-W09

Question list

List of questions

Question 1

(0)

You plan to use multi-protocol BGP to implement dynamic VRF route leaking on an ArubaOS-CX switch. Is this a rule for the setup? Solution: You can only leak routes between up to three VRFs.

Question 2

(0)

You plan to use multi-protocol BGP to implement dynamic VRF route leaking on an ArubaOS-CX switch. Is this a rule for the setup? Solution: You cannot leak multicast routes.

Question 3

(0)

A customer's servers use ISCSI, and they send data and storage traffic on the same pair of I OGbE links. Is this a best practice for supporting the ISCSI requirements? Solution: Set up dedicated sw

Question 4

(0)

Is this a guideline for establishing a Virtual Switching Extension (VSX) Inter-Switch Link (ISL) between two ArubaOS-CX switches? Solution: Use the same speed on every link In the ISL.

Question 5

(0)

AtubaOS-CX switches are acting as Virtual Extensible LAN (VXLAN) Tunnel Endpoints (VTEPs) WITHOUT Ethernet VPN (EVPN). Does this correctly describe how the VTEPs handle VXLAN traffic forwarding? S

Question 6

(0)

Is this how you should position switches in the ArubaOS-CX portfolio for data center networks? Solution: Deploy Aruba 83xx switches as data center leaf switches.

Question 7

(0)

Refer to the exhibit. Switch-1 and Switch-2 ate ArubaOS-CX switches that implement VXLAN WITHOUT Ethernet VPN (EVPN). Switch-2 uses the same VNI-to-VLAN mappings as Switch-1. Is this how the spec

Question 8

(0)

You want to use NetEdit to configure an AtubaOS-CX switch. Is this a minimum requirement for setting up communications between the switch and NetEdit? Solution: Enable the REST interface in read-o

Question 9

(0)

You want to use NetEdit to configure an AtubaOS-CX switch. Is this a minimum requirement for setting up communications between the switch and NetEdit? Solution: Make sure that the SSH server is en

Question 10

(0)

Does this correctly describe the ArubaOS-CX architecture? Solution: The AtubaOS-CX software is based on the ArubaOS-Switch software and adds data center features.

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibit. You need to set up an ArubaOS-CX switch to implement Virtual Extensible LAN (VXLAN) WITHOUT Ethernet VPN (EVPN). The exhibit Indicates which servers should be part of the same VXLANs and the desired VNls for the VXLANs. Assume that the network is already configured to permit each ArubaOS-CX switch to reach each other switch's loopback interface. Is this part of the process for setting up VXLAN to meet the requirements? Solution: On Switch-1, add VNIs 5010 and 5020 to the same VXLAN interface.

Is this a difference between a typical data center network's requirements and a typical campus network's requirements? Solution: Data center network traffic flows are typically east-west whereas while campus networks experience more north-south traffic.

Is this a way that Virtual Switching Extension (VSX) differs from Virtual Switching Framework (VSF)? Solution: VSX features a dual control plane while VSF features a single control plane.

Is this a difference between a typical data center network's requirements and a typical campus network's requirements? Solution: Data center networks are typically less oversubscribed than campus networks.

You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address. Is this what you should do? Solution: omit the device-specific settings from the configuration plan and include them in command scripts instead.

Is this a requirement for implementing Priority Flow Control (PFC) on an ArubaOS-CX switch interface? Solution: configuring a DCBX application priority on the interface

Refer to the exhibit. Switch-1 and Switch-2 ate ArubaOS-CX switches that implement VXLAN WITHOUT Ethernet VPN (EVPN). Switch-2 uses the same VNI-to-VLAN mappings as Switch-1. Is this how the specified servers communicate? Solution: Server 1 and Server 4 require routing services within the VXLANs to communicate with each other.

Refer to the exhibit. Switch-1, Switch-2, and the router run OSPF on LAG 100, which is a Layer 3 LAG. Does this correctly explain how to control how core-to-access traffic Is forwarded? Solution: To force the router to use both links, ensure that active gateway is enabled on LAG 100 on both Switch-1 and Switch-2.

Is this a guideline for establishing a Virtual Switching Extension (VSX) Inter-Switch Link (ISL) between two ArubaOS-CX switches? Solution: Reserve the ISL for control plane traffic only.

Is this a use case for disabling split-recovery mode on ArubaOS-CX switches in a Virtual Switching Extension (VSX) fabric? Solution: In situations in which the primary switch fails and then reboots, you want to make the primary switch wait a period before it takes over as the primary switch.

Question 9 - HPE2-W09 discussion

Report

You want to use NetEdit to configure an AtubaOS-CX switch.

Is this a minimum requirement for setting up communications between the switch and NetEdit?

Solution: Make sure that the SSH server is enabled.

A.

Yes

B.

No

Show Answer

asked 16/09/2024

Pay Ametovski

38 questions

User

Your answer: A B

0 comments

Sorted by

Leave a comment first