Home

Home / Fortinet / NSE6_FSW-7.2

Question list

List of questions

Question 1

(0)

How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?

Question 2

(0)

Refer to the exhibit. The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports, and these ports are connected to endpoints which are powered by PoE. Which configurati

Question 3

(0)

Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)

Question 4

(0)

Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?

Question 5

(0)

What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?

Question 6

(0)

Which packet capture method allows FortiSwitch to capture traffic on trunks and management interfaces?

Question 7

(0)

Which Ethernet frame can create Layer 2 flooding due to all bytes on the destination MAC address being set to all FF?

Question 8

(0)

Which is a requirement to enable SNMP v2c on a managed FortiSwitch?

Question 9

(0)

Refer to the diagnostic output: Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

Question 10

(0)

Refer to the exhibit. Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becom

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibits. You are asked to ensure that managed FortiSwitch devices are reachable by other devices, such as SNMP and other management tools across your network. Which setting must you configure to ensure traffic from other devices in the network reaches FortiSwitch?

Refer to the exhibit. Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding. Why is port1 in the discarding state?

Exhibit. The exhibit shows the current status of the ports on the managed FortiSwitch. Access-1. Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

Exhibit. Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

Exhibit. port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)

Which Ethernet frame can create Layer 2 flooding due to all bytes on the destination MAC address being set to all FF?

Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?

Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)

Which two rules used by MSTP are similar to rules used by other STP methods? (Choose two.)

Refer to the diagnostic output: Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

Question 5 - NSE6_FSW-7.2 discussion

Report

What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?

A.

FortiGate multi-tenancy

B.

Multi-chassis link aggregation trunk

C.

FortiGate clustering protocol

D.

FortiLink split interface

Show Answer

asked 18/09/2024

Charl Grove

32 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first