ExamGecko
Search Search Login
Home Home / Fortinet / NSE7_NST-7.2
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which exchange lakes care of DoS protection in IKEv2?
Refer to the exhibit, which shows the omitted output of a real-time OSPF debug Which statement is false?
Exhibit. Refer to the exhibit, which shows partial outputs from two routing debug commands. Why is the port 2 default route not in the second command output?
Refer to the exhibit, which shows the omitted output of FortiOS kernel slabs. Which statement is true?
Which two conditions would prevent a static route from being added to the routing table? (Choose two.)
Refer to the exhibit, which shows a truncated output of a real-time LDAP debug. What two conclusions can you draw from the output? (Choose two.)
There are four exchanges during IKEv2 negotiation. Which sequence is correct?
Refer to the exhibits, which show the configuration on FortiGate and partial session information for internet traffic from a user on the internal network. If the priority on route ID _ were changed from 10 to 0, what would happen to traffic matching that user session?
Exhibit. Refer to the exhibit, which shows the omitted output of diagnose npu np6 port-list on a FortiGate1500D. An administrator is unable to analyze traffic flowing between port1 and port7 using the diagnose sniffer command. Which two commands allow the administrator to view the traffic? (Choose two.) A) B) C) D)
Which three conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)

Question 13 - NSE7_NST-7.2 discussion

Report
Export

Refer to the exhibit, which shows the output of a BGP debug command.

Which statement explains why the state of the 10.200.3.1 peer is Connect?

A.
The local router initiated the BGP session to 10.200.3.1 but did not receive a response.
Answers
A.
The local router initiated the BGP session to 10.200.3.1 but did not receive a response.
B.
The local router is receiving BGP keepalives from the remote peer, but the local peer has not received the OpenConf inn yet.
Answers
B.
The local router is receiving BGP keepalives from the remote peer, but the local peer has not received the OpenConf inn yet.
C.
The router 10.200.3.1 has authentication configured for BGP and the local router does not.
Answers
C.
The router 10.200.3.1 has authentication configured for BGP and the local router does not.
D.
The local router has a different AS number than the remote peer.
Answers
D.
The local router has a different AS number than the remote peer.
Suggested answer: A

Explanation:

The BGP summary output shows the state of the 10.200.3.1 peer as 'Connect.' This state indicates that the local router has attempted to initiate a BGP session with the peer, but the peer has not yet responded to the initial connection request.

State Explanation: The 'Connect' state in BGP indicates that the TCP connection has been initiated but is waiting for a response. If the peer does not respond within the configured timers, the session will transition to the 'Active' state and retry the connection.

Possible Causes: This can occur due to network issues preventing the peer from responding, a misconfiguration on the peer device, or issues like access control lists (ACLs) blocking the BGP traffic.

To troubleshoot, check the connectivity between the routers, ensure that the BGP configurations on both sides match, and verify that there are no firewalls or ACLs blocking the BGP packets.

Fortinet Documentation on BGP Troubleshooting

Fortinet Community Discussion on BGP State Issues

Show Answer
asked 18/09/2024
frederic dohen
36 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms