Home / Juniper / JN0-480

Question list

List of questions

Question 1

(0)

In the Juniper Apstra Ul. you are creating a VNI pool for virtual networks. In this scenario, which VNI range is acceptable?

Question 2

(0)

Exhibit. Which two statements ate correct about the graph query output shown in the exhibit? (Choose two.)

Question 3

(0)

Which statement is correct about the Juniper Apstra Rendered configuration?

Question 4

(0)

Multilenancy for applications is achieved by creating virtual networks (VNs) within which construct?

Question 5

(0)

What does EVPN use lo identity which remote leaf device advertised the EVPN route?

Question 6

(0)

Exhibit. You connect two single-homed servers using Juniper Apstra as shown in the exhibit. You are using the ERB design blueprint with two virtual networks in a common routing zone. In this sce

Question 7

(0)

In the Juniper Apstra design phase, which object dictates port count, port speed, and how the ports would be used?

Question 8

(0)

You want to keep virtual networks isolated from each other within the Juniper Apstra system. In this scenario, what are three ways to accomplish this task? (Choose three.)

Question 9

(0)

Exhibit. The 10.100.0.0/16 route is being advertised into your BGP IP fabric. ECMP load balancing has been properly enabled on all devices In this scenario, how many routes will the leaf device

Question 10

(0)

Using the Juniper Apstra multitenancy capabilities, which approach will allow a tenant to interconnect two different routing zones?

Question 31 - JN0-480 discussion

In the Juniper Apstra Ul. which three resources are assigned under the Resources menu? (Choose three.)

VTEP pools

ASN pools

VNI pools

logical device pools

IP address pools

Suggested answer: B, C, E

Explanation:

In the Juniper Apstra UI, the Resources menu allows you to create and manage global and local resources that are used for various elements of the network design and configuration. The Resources menu includes the following three types of resources that can be assigned to the network devices and virtual networks:

ASN pools: These are pools of autonomous system numbers (ASNs) that are used for the underlay routing protocol (EBGP) between the leaf and spine devices. You can create ASN pools with either 2-byte or 4-byte ASNs, and assign them to the logical devices in the blueprint.

VNI pools: These are pools of virtual network identifiers (VNIs) that are used for the overlay network (VXLAN) between the end hosts. You can create VNI pools with a range of VNIs, and assign them to the virtual networks in the blueprint.

IP address pools: These are pools of IPv4 or IPv6 addresses that are used for various purposes in the network, such as the loopback addresses for the devices, the IP prefixes for the virtual networks, the host IP addresses for the end hosts, and the gateway IP addresses for the IRB interfaces. You can create IP address pools with a range of IP addresses, and assign them to the logical devices and virtual networks in the blueprint.

The following two types of resources are not assigned under the Resources menu:

VTEP pools: These are not resources that can be created or assigned by the user. VTEPs are VXLAN tunnel endpoints that are automatically generated by the Apstra server based on the loopback IP addresses of the devices. VTEPs are used as the source and destination IP addresses for the VXLAN tunnels in the overlay network.

Logical device pools: These are not resources that can be created or assigned by the user. Logical device pools are groups of logical devices that share the same role, interface map, and resource assignments in the blueprint. Logical device pools are used to simplify the network design and configuration by applying the same settings to multiple devices.

Resources Introduction

ASN Pools (Resources)

VNI Pools (Resources)

IP Address Pools (Resources)

Show Answer

asked 18/09/2024

Alain Bijl

40 questions

Your answer: A B C D E

0 comments

Sorted by