Home

Home / Juniper / JN0-480

Question list

List of questions

Question 1

(0)

In the Juniper Apstra Ul. you are creating a VNI pool for virtual networks. In this scenario, which VNI range is acceptable?

Question 2

(0)

Exhibit. Which two statements ate correct about the graph query output shown in the exhibit? (Choose two.)

Question 3

(0)

Which statement is correct about the Juniper Apstra Rendered configuration?

Question 4

(0)

Multilenancy for applications is achieved by creating virtual networks (VNs) within which construct?

Question 5

(0)

What does EVPN use lo identity which remote leaf device advertised the EVPN route?

Question 6

(0)

Exhibit. You connect two single-homed servers using Juniper Apstra as shown in the exhibit. You are using the ERB design blueprint with two virtual networks in a common routing zone. In this sce

Question 7

(0)

In the Juniper Apstra design phase, which object dictates port count, port speed, and how the ports would be used?

Question 8

(0)

You want to keep virtual networks isolated from each other within the Juniper Apstra system. In this scenario, what are three ways to accomplish this task? (Choose three.)

Question 9

(0)

Exhibit. The 10.100.0.0/16 route is being advertised into your BGP IP fabric. ECMP load balancing has been properly enabled on all devices In this scenario, how many routes will the leaf device

Question 10

(0)

Using the Juniper Apstra multitenancy capabilities, which approach will allow a tenant to interconnect two different routing zones?

Open VPLUS File

Convert VPLUS to PDF

Related questions

You want to keep virtual networks isolated from each other within the Juniper Apstra system. In this scenario, what are three ways to accomplish this task? (Choose three.)

Exhibit. Referring to the exhibit, how many broadcast domains will an Ethernet frame pass through when traversing the IP fabric from Server A to Server B?

Multilenancy for applications is achieved by creating virtual networks (VNs) within which construct?

Which two statements are correct regarding a pristine configuration in Juniper Apstra? (Choose two.)

A member of your organization made changes to a predefined interface map using Juniper Apstra. Which two statements are correct in this scenario? (Choose two.)

Exhibit. Referring to the exhibit, how do you display the IPv6 subnets lot all of the listed VXLANs?

Which statement is true when onboarding a Juniper Networks device using a Juniper Apstra ZTP server?

Using the Juniper Apstra multitenancy capabilities, which approach will allow a tenant to interconnect two different routing zones?

When working with logical devices, you specify where each port group is connected. In this scenario, which two Juniper Apstra Ul options are available to the operator? {Choose two.)

Exhibit. Which two statements about ESI values are correct for the server connections to the fabric shown in the exhibit? (Choose two.)

Question 62 - JN0-480 discussion

Report

Which two statements are correct regarding a pristine configuration in Juniper Apstra? (Choose two.)

A.

It is the configuration file placed on the device when decommissioning the device.

B.

It is the device's currently active configuration.

C.

It Is the configuration file on a device before acknowledgment in Apstra.

D.

It is the device's previously active configuration.

Suggested answer: A, C

Explanation:

A pristine configuration in Juniper Apstra is the configuration file that is used to onboard a device into the Apstra software application.A pristine configuration contains the minimum settings that are required for the device to communicate with the Apstra server, such as the hostname, management IP address, username, password, and SSH key1. A pristine configuration has the following characteristics:

It is the configuration file placed on the device when decommissioning the device. This is because when a device is decommissioned from the Apstra software application, it is reverted back to its pristine configuration, which removes all the network configuration and services that were applied by the Apstra software application.This allows the device to be reused or repurposed for another network2.

It is the configuration file on a device before acknowledgment in Apstra. This is because when a device is onboarded into the Apstra software application, it is initially in the discovery state, which means that the device is discovered by the Apstra server, but not yet acknowledged by the user. In the discovery state, the device has the pristine configuration, which can be viewed and edited by the user.Once the user acknowledges the device, the device moves to the deployed state, which means that the device is ready to receive the network configuration and services from the Apstra software application3.

The following two statements are incorrect in this scenario:

It is the device's currently active configuration. This is not true, because the pristine configuration is not the device's currently active configuration, unless the device is in the discovery state or the decommissioned state.In the deployed state, the device's currently active configuration is the network configuration and services that are applied by the Apstra software application, which are based on the blueprint and the intent3.

It is the device's previously active configuration. This is not true, because the pristine configuration is not the device's previously active configuration, unless the device is in the decommissioned state. In the discovery state, the pristine configuration is the device's initial configuration, which may or may not be the same as the device's previous configuration before being onboarded into the Apstra software application.In the deployed state, the device's previously active configuration is the network configuration and services that were applied by the Apstra software application before the last commit3.

Pristine Config

Decommission Device

Device States

Show Answer

asked 18/09/2024

Jarrell John Garcia

37 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first