Home / Juniper / JN0-636

Question list

List of questions

Question 1

(0)

Exhibit You are using trace options to verity NAT session information on your SRX Series device Referring to the exhibit, which two statements are correct? (Choose two.)

Question 2

(0)

Exhibit You are asked to establish an IBGP peering between the SRX Series device and the router, but the session is not being established. In the security flow trace on the SRX device, packet dro

Question 3

(0)

SRX Series device enrollment with Policy Enforcer fails To debug further, the user issues the following command show configuration services security—intelligence url https : //cloudfeeds . argon .

Question 4

(0)

Exhibit Referring to the exhibit, which three statements are true? (Choose three.)

Question 5

(0)

Exhibit You configure a traceoptions file called radius on your returns the output shown in the exhibit What is the source of the problem?

Question 6

(0)

Exhibit You have configured the SRX Series device to switch packets for multiple directly connected hosts that are within the same broadcast domain However, the traffic between two hosts in the s

Question 7

(0)

You are asked to deploy filter-based forwarding on your SRX Series device for incoming traffic sourced from the 10.10 100 0/24 network in this scenario, which three statements are correct? (Choose

Question 8

(0)

You are connecting two remote sites to your corporate headquarters site. You must ensure that all traffic is secured and sent directly between sites In this scenario, which VPN should be used?

Question 9

(0)

You are asked to detect domain generation algorithms Which two steps will accomplish this goal on an SRX Series firewall? (Choose two.)

Question 10

(0)

In Juniper ATP Cloud, what are two different actions available in a threat prevention policy to deal with an infected host? (Choose two.)

Question 90 - JN0-636 discussion

You want to enable inter-tenant communica on with tenant system.

In this Scenario, Which two solutions will accomplish this task?

interconnect EVPN switch

interconnect VPLS switch

external router

logical tunnel interface

Suggested answer: C, D

Explanation:

To enable inter-tenant communication with tenant system, you need to use an external router or a logical tunnel interface. The other options are incorrect because:

A) Interconnecting EVPN switch is not a valid solution for inter-tenant communication with tenant system. EVPN (Ethernet VPN) is a technology that provides layer 2 connectivity over an IP network. It can be used to connect different logical systems on the same device, but not tenant systems. Tenant systems are isolated from each other and do not share the same layer 2 domain1.

B) Interconnecting VPLS switch is also not a valid solution for inter-tenant communication with tenant system. VPLS (Virtual Private LAN Service) is another technology that provides layer 2 connectivity over an IP network. It can also be used to connect different logical systems on the same device, but not tenant systems. Tenant systems are isolated from each other and do not share the same layer 2 domain1.

Therefore, the correct answer is C and D. You need to use an external router or a logical tunnel interface to enable inter-tenant communication with tenant system. To do so, you need to perform the following steps:

For external router, you need to connect the external router to the interfaces of the tenant systems that you want to communicate with. You also need to configure the routing protocols and policies on the external router and the tenant systems to exchange routes and traffic. The external router acts as a gateway between the tenant systems and provides layer 3 connectivity2.

For logical tunnel interface, you need to create a logical tunnel interface on the device and assign it to a tenant system. You also need to configure the IP address and routing protocols on the logical tunnel interface and the tenant systems that you want to communicate with. The logical tunnel interface acts as a virtual link between the tenant systems and provides layer 3 connectivity3.

Reference:

Tenant Systems Overview

Example: Configuring Inter-Tenant Communication Using External Router

Example: Configuring Inter-Tenant Communication Using Logical Tunnel Interface

Show Answer

asked 18/09/2024

David Murinda

42 questions

Your answer: A B C D

0 comments

Sorted by