ExamGecko
Search Search Login
Home Home / VCE / 210-015
Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

You are implementing 32 new UCS B230 M3 blades into an existing Vblock System with 16 blades. After powering the new blades on, and migrating them to the Cisco Nexus 1000V, you notice that half of the new blades no longer respond to any network traffic. What is the cause?
You power on a Vblock System 320 and look at the Maps tab of an ESXi server in vCenter's Hosts And Clusters view and see an ESXi server with a red "x" over it. What is causing the ESX server problem?
A VM on the Vblock System 320 is unable to communicate on the customer network. When examining the virtual machine, you notice it has the same port group as the other VMs on the same ESXi server. Which action must you perform to resolve the problem?
Which database platform is supported with VMware 5.x in a Vblock System?
While upgrading five hosts in a vSphere cluster, the maintenance window ends. The customer does not allow you to extend the window, so now the cluster is running the hosts at different build levels. There are two hosts at the new build version, and three hosts at the previous build version. There are 11 virtual machines protected by VMware Fault Tolerance in the cluster. You now see the following error No suitable host can be found to place the Fault Tolerance Secondary VM for virtual machine SalesVM. What is the cause of this error?
The ESXi 5.0 servers appear to have hardware problems after you have powered up the Vblock System 320. You want to view the log files for the ESXi servers. What are two ways to accomplish this task? (Choose two.)
During the deployment of a Vblock System, it was discovered that the Cisco Nexus 1000V VSM virtual machines were residing upon the same vSphere host in the AMP. To comply with VCE best practices for separating the Cisco Nexus 1000V VSM virtual machines, what is missing?
Which two methods would you use to deploy an ESXi image created with Image Builder CLI? (Choose two.)
In a standard Vblock System 300 configuration with two vHBAs, the VNX Storage Processor A (SP-A) has rebooted. How will the hosts be impacted?
You want to configure vMotion on a virtual switch in a Vblock System 320. Which network configuration is required?

Question 36 - 210-015 discussion

Report
Export

In a Vblock 320 Unified Networking environment, a UCS service profile is unable to locate its boot device.

Which two statements are valid troubleshooting steps? (Choose two.)

A.
Verify that the targets in the SAN boot policy match the zoning and the masking on the array.
Answers
A.
Verify that the targets in the SAN boot policy match the zoning and the masking on the array.
B.
Verify that the vHBAs are logging into the SAN fabrics by examining the Fabric Login (FLOGI) database on the Cisco MDS switches.
Answers
B.
Verify that the vHBAs are logging into the SAN fabrics by examining the Fabric Login (FLOGI) database on the Cisco MDS switches.
C.
Verify that PowerPathVE can see all paths to the device.
Answers
C.
Verify that PowerPathVE can see all paths to the device.
D.
Verify that the vHBAs are logging into the SAN fabrics by examining the Fabric Login (FLOGI) database on the Cisco Nexus 5000 series switches.
Answers
D.
Verify that the vHBAs are logging into the SAN fabrics by examining the Fabric Login (FLOGI) database on the Cisco Nexus 5000 series switches.
Suggested answer: A, D

Explanation:

Answer is Modified.

Show Answer
asked 23/09/2024
Tim Baas
42 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms