While examining excessive traffic on the network, it is noted that all incoming packets on an interface appear to be allowed even though an IPv4 ACL is applied to the interface.Which two misconfigurations cause this behavior? (Choose two)

A matching permit statement is too high in the access test

A matching permit statement is too broadly defined

The packets fail to match any permit statement

A matching permit statement is too high in the access test

A matching permit statement is too broadly defined

A matching deny statement is too high in the access list

Why does a switch flood a frame to all ports?

The destination MAC address of the frame is unknown.

The frame has zero destination MAC addresses.

The source MAC address of the frame is unknown

The source and destination MAC addresses of the frame are the same

The destination MAC address of the frame is unknown.

Refer to the exhibit. The nip server 192.168.0.3 command has been configured on router 1 to make it an NTP client of router 2. Which command must be configured on router 2 so that it operates in server-only mode and relies only on its internal clock?

Router2(config)#ntp server 192.168.0.2

Router2(config)#ntp server 172.17.0.1

Router2(config)#ntp server 192.168.0.2

A network administrator enabled port security on a switch interface connected to a printer. What is the next configuration action in order to allow the port to learn the MAC address of the printer and insert it into the table automatically?

enable dynamic MAC address learning

implement static MAC addressing.

implement auto MAC address learning

Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites.Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another?(Choose two.)

Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router.

Configure the ipv6 route 2012::/126 2023::2 command on the Washington router.

Configure the ipv6 route 2012::/126 2023::1 command on the Washington router.

Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router.

Configure the Ipv6 route 2012::/126 s0/0/0 command on the Atlanta router.

Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router.

Configure the ipv6 route 2012::/126 2023::2 command on the Washington router.

Where is the interface between the control plane and data plane within the software-defined architecture?

control layer and the infrastructure layer

application layer and the infrastructure layer

application layer and the management layer

control layer and the application layer

What are two benefits of using the PortFast feature? (Choose two )

Enabled interfaces are automatically placed in listening state

Enabled interfaces come up and move to the forwarding state immediately

Enabled interfaces are automatically placed in listening state

Enabled interfaces come up and move to the forwarding state immediately

Enabled interfaces never generate topology change notifications.

Enabled interfaces that move to the learning state generate switch topology change notifications

Enabled interfaces wait 50 seconds before they move to the forwarding state

What are two characteristics of an SSID? (Choose Two)

It uniquely identifies an access point in a WLAN

IT provides secured access to a WLAN

It can be hidden or broadcast in a WLAN

It uniquely identifies an access point in a WLAN

It uniquely identifies a client in a WLAN

It is at most 32 characters long.

IT provides secured access to a WLAN

What is the purpose of an SSID?

It differentiates traffic entering access posits

It identities an individual access point on a WLAN

Refer to the exhibit. A network administrator has been tasked with securing VTY access to a router Which access-list entry accomplishes this task?

access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10 0.0.0.255 eq ssh

access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eq scp

access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eq telnet

access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10 0.0.0.255 eq https

Which action is taken by a switch port enabled for PoE power classification override?

Should a monitored port exceeds the maximum administrative value for power, the port is shutdown and err-disabled

When a powered device begins drawing power from a PoE switch port a syslog message is generated

As power usage on a PoE switch port is checked data flow to the connected device is temporarily paused

If a switch determines that a device is using less than the minimum configured power it assumes the device has failed and disconnects

Should a monitored port exceeds the maximum administrative value for power, the port is shutdown and err-disabled

What are two reasons that cause late collisions to increment on an Ethernet interface? (Choose two)

when the cable length limits are exceeded

when one side of the connection is configured for half-duplex

when the sending device waits 15 seconds before sending the frame again

when the cable length limits are exceeded

when one side of the connection is configured for half-duplex

when Carrier Sense Multiple Access/Collision Detection is used

when a collision occurs after the 32nd byte of a frame has been transmitted

What are two characteristics of a controller-based network? (Choose two)

It uses northbound and southbound APIs to communicate between architectural layers

It moves the control plane to a central point.

The administrator can make configuration updates from the CLI

It uses northbound and southbound APIs to communicate between architectural layers

It moves the control plane to a central point.

It decentralizes the control plane, which allows each device to make its own forwarding decisions

It uses Telnet to report system issues.

What is the benefit of configuring PortFast on an interface?

After the cable is connected, the interface is available faster to send and receive user data

After the cable is connected, the interface uses the fastest speed setting available for that cable type

After the cable is connected, the interface is available faster to send and receive user data

The frames entering the interface are marked with higher priority and then processed faster by a switch.

Real-time voice and video frames entering the interface are processed faster

An engineer configures interface Gi1/0 on the company PE router to connect to an ISP Neighbor discovery is disabled Which action is necessary to complete the configuration if the ISP uses third-party network devices?

Disable Cisco Discovery Protocol on the interface

Enable LLDP-MED on the ISP device

Which type of organization should use a collapsed-core architecture?

small and needs to reduce networking costs currently

large and requires a flexible, scalable network design

large and must minimize downtime when hardware fails

small and needs to reduce networking costs currently

small but is expected to grow dramatically in the near future

What is a capability of FTP in network management operations?

uses separate control and data connections to move files between server and client

encrypts data before sending between data resources

devices are directly connected and use UDP to pass file information

uses separate control and data connections to move files between server and client

offers proprietary support at the session layer when transferring data

What is a function of a Layer 3 switch?

move frames between endpoints limited to IP addresses

transmit broadcast traffic when operating in Layer 3 mode exclusively

forward Ethernet frames between VLANs using only MAC addresses

flood broadcast traffic within a VLAN

Refer to the exhibit. An engineer is configuring the HO router. Which IPv6 address configuration must be applied to the router fa0'1 interface for the router to assign a unique 64-brt IPv6 address to Itself?

ipv6 address 2001:DB8:0:1:C601:42FF:FE0F:7/64

ipv6 address 2001:DB8:0:1:C601:42FE:800F:7/64

ipv6 address 2001 :DB8:0:1:FFFF:C601:420F:7/64

iov6 address 2001 :DB8:0:1:FE80:C601:420F:7/64

Which action is taken by the data plane within a network device?

forwards traffic to the next hop

constructs a routing table based on a routing protocol

provides CLI access to the network device

looks up an egress interface in the forwarding information base

What is a function of a Next-Generation IPS?

correlates user activity with network events

makes forwarding decisions based on learned MAC addresses

serves as a controller within a controller-based network

integrates with a RADIUS server to enforce Layer 2 device authentication rules

correlates user activity with network events

Refer to the exhibit. Which route must be configured on R1 so that OSPF routing is used when OSPF is up. but the server is still reachable when OSPF goes down?

ip route 10.1.1.10 255.255.255.255 gi0/0 125

ip route 10.1.1.10 255.255.255.255 172.16.2.2 100

ip route 10.1.1.0 255.255.255.0 gi0/1 125

ip route 10.1.1.0 255.255.255.0 172.16.2.2 100

ip route 10.1.1.10 255.255.255.255 gi0/0 125

Refer to the exhibit. Users need to connect to the wireless network with IEEE 802. 11r-compatible devices. The connection must be maintained as users travel between floors or to other areas in the building What must be the configuration of the connection?

Enable Fast Transition and select the FT 802.1x option.

Select the WPA Policy option with the CCKM option.

Enable Fast Transition and select the FT 802.1x option.

Enable Fast Transition and select the FT PSK option.

Cisco 200-301 Practice Test 13 - Free Online Exam Questions 481-520

An engineer must configure traffic for a VLAN that is untagged by the switch as it crosses a trunk link.

Which command should be used?

Become a Premium Member for full access

Unlock Premium Member

Cisco 200-301 Practice Test 13

Question

Cisco 200-301 Practice Tests

Practice Tests