The clients and OHCP server reside on different subnets. Which command must be used to forward requests and replies between clients on the 10.10.0.1/24 subnet and the DHCP server at 192.168.10.1?

ip default-gateway 192.168.10.1

Refer to the exhibit. Rapid PVST+ mode is on the same VLAN on each switch. Which switch becomes the root bridge and why?

SW3, because its priority is the highest

SW2, because its MAC address is the highest

SW3, because its priority is the highest

SW4, because its priority is highest and its MAC address is lower

SW1, because its priority is the lowest and its MAC address is higher

A network engineer is upgrading a small data center to host several new applications, including server backups that are expected to account for up to 90% of the bandwidth during peak times. The data center connects to the MPLS network provider via a primary circuit and a secondary circuit. How does the engineer inexpensively update the data center to avoid saturation of the primary circuit by traffic associated with the backups?

Assign traffic from the backup servers to a dedicated switch.

Configure a dedicated circuit for the backup traffic.

Place the backup servers in a dedicated VLAN.

Advertise a more specific route for the backup traffic via the secondary circuit.

Refer to the exhibit. A network engineer executes the show ip route command on router D. What is the next hop to network 192.168 1 0/24 and why?

The next hop is 10.0.2.1 because it is a link-state routing protocol

The next hop is 10.0.2.1 because it uses distance vector routing

The next hop is 10.0.2.1 because it is a link-state routing protocol

The next hop is 10.0.0.1 because it has a better administrative distance

The next hop is 10.0.0.1 because it has a higher metric.

Refer to the exhibit. A Cisco engineer creates a new WLAN called lantest. Which two actions must be performed so that only high-speed 2.4-Ghz clients connect? (Choose two.)

Enable the Broadcast SSID option

Set the Radio Policy option to 802 11g Only.

Set the Radio Policy option to 802.11a Only.

Set the Interface/Interface Group(G) to an interface other than guest

What is the role of nonoverlapping channels in a wireless environment?

to stabilize the RF environment

A router has two static routes to the same destination network under the same OSPF process. How does the router forward packets to the destination if the next-hop devices are different?

The router load-balances traffic over all routes to the destination.

The router chooses the route with the oldest age.

The router load-balances traffic over all routes to the destination.

The router chooses the next hop with the lowest MAC address.

The router chooses the next hop with the lowest IP address.

Refer to the exhibit. Which two values does router R1 use to determine the best path to reach destinations in network 1,0.0.0/8? (Choose two.)

highest administrative distance

lowest cost to reach the next hop

Refer to the exhibit. Host A switch interface is configured in VLAN 2. Host D sends a unicast packet destined for the IP address of host A. What does the switch do when it receives the frame from host D?

It shuts down the source port and places It In err-disable mode.

It drops the frame from the MAC table of the switch.

It shuts down the source port and places It In err-disable mode.

It floods the frame out of every port except the source port.

Which properly is shared by 10GBase-SR and 10GBase-LR interfaces?

Both require fiber cable media for transmission.

Both require UTP cable media for transmission.

Both use the single-mode fiber type.

Both use the multimode fiber type.

Refer to the exhibit. What does route 10.0.1.3/32 represent in the routing table?

all hosts in the 10.0.1.0 subnet

Refer to the exhibit. A network administrator must permit traffic from the 10.10.0.0/24 subnet to the WAN on interlace Seria10. What is the effect of the configuration as the administrator applies the command?

The sourced traffic from IP range 10.0.0.0 -10.0.0.255 is allowed on Seria10.

The permit command fails and returns an error code.

The router accepts all incoming traffic to Seria10 with the last octet of the source IP set to 0.

The sourced traffic from IP range 10.0.0.0 -10.0.0.255 is allowed on Seria10.

The router fails to apply the access list to the interface.

What is the role of community strings in SNMP operations?

It serves as a password lo protect access to MIB objects.

It serves as a sequence tag on SNMP traffic messages.

It serves as a password lo protect access to MIB objects.

It passes the Active Directory username and password that are required for device access

It translates alphanumeric MIB output values to numeric values.

What are two characteristics of a small office / home office connection environment? (Choose two.)

It supports between 1 and 50 users.

A router port connects to a broadband connection.

It requires 10Gb ports on all uplinks.

It supports between 50 and 100 users.

It supports between 1 and 50 users.

It requires a core, distribution, and access layer architecture.

A router port connects to a broadband connection.

What is the definition of backdoor malware?

malicious code that is installed onto a computer to allow access by an unauthorized user

malicious code with the main purpose of downloading other malicious code

malicious program that is used to launch other malicious programs

malicious code that infects a user machine and then uses that machine to send spam

Refer to the exhibit. Which two values does router R1 use to identify valid routes for the R3 loopback address 1.1.1.3/32?(Choose two.)

lowest cost to teach the next hop

highest administrative distance

Refer to the exhibit. An engineer is updating the management access configuration of switch SW1 to allow secured, encrypted remote configuration. Which two commands or command sequences must the engineer apply to the switch? (Choose two.)

SW1(config)#line vty 0 15 SW1(config-line)#transport input ssh

SW1(config)# crypto key generate rsa

SW1(config)#enable secret ccnaTest123

SW1(config)#username NEW secret R3mote123

SW1(config)#line vty 0 15 SW1(config-line)#transport input ssh

SW1(config)# crypto key generate rsa

SW1(config)# interface f0/1 SW1(confif-if)# switchport mode trunk

SIP-based Call Admission Control must be configured in the Cisco WLC GUI. SIP call-snooping ports are configured. Which two actions must be completed next? (Choose two.)

Enable traffic shaping for the LAN interlace of the WLC.

Configure two different QoS rotes tor data and voice traffic.

Set the QoS level to silver or greater for voice traffic.

Set the QoS level to platinum for voice traffic.

Enable Media Session Snooping on re WLAN.

Enable traffic shaping for the LAN interlace of the WLC.

Configure two different QoS rotes tor data and voice traffic.

What is a benefit of using private IPv4 addressing?

Multiple companies can use the same addresses without conflicts.

Direct connectivity is provided to internal hosts from outside an enterprise network.

Communication to the internet Is reachable without the use of NAT.

All external hosts are provided with secure communication to the Internet.

Refer to the exhibit. An engineer must configure a floating static route on an external EIGRP network. The destination subnet is the /29 on the LAN Interface of R86. Which command must be executed on R14?

ip route 10.80.65.0.255.255.248.0.10.73.65.66.171

ip route 10.80.65.0.255.255.248.0.10.73.65.66.1

ip route 10.80.65.0.255.255.255..240 fa0/1 89

ip route 10.80.65.0.255.255.248.0.10.73.65.66.171

ip route 10.80.65.0.0.0.224.10.80.65.0. 255

What is the functionality of the Cisco DNA Center?

software-defined controller for automaton of devices and services

console server that permits secure access to all network devices

IP address cool distribution scheduler

software-defined controller for automaton of devices and services

Refer to Exhibit. Refer to the exhibit. The router R1 is in the process of being configured. Routers R2 and R3 are configured correctly for the new environment. Which two commands must be configured on R1 for PC1 to communicate to all PCs on the 10.10.10.0/24 network? (Choose two.)

ip route 10.10.10.0 255.255.255.0 192.168.2.3

ip route 10.10.10.0 255.255.255.248 192.168.2.2

ip route 10.10.10.0 255.255.255.0 192.168.2.3

ip route 10.10.10.10 255.255.255.255 192.168.2.2

ip route 10.10.10.10 255.255.255.255 g0/1

ip route 10.10.10.8 255.255.255.248 g0/1

ip route 10.10.10.0 255.255.255.248 192.168.2.2

Which protocol is used in Software Defined Access (SDA) to provide a tunnel between two edge nodes in different fabrics?

Generic Router Encapsulation (GRE)

Virtual Local Area Network (VLAN)

Refer to the exhibit. The network engineer is configuring a new WLAN and is told to use a setup password for authentication instead of the RADIUS servers. Which additional set of tasks must the engineer perform to complete the configuration?

Select WPA2 Policy Disable PMF Enable PSK

Disable PMF Enable PSK Enable 802.1x

Select WPA Policy Enable CCKM Enable PSK

Select WPA Policy Select WPA2 Policy Enable FT PSK

Select WPA2 Policy Disable PMF Enable PSK

Cisco 200-301 Practice Test 20 - Free Online Exam Prep & Questions

Refer to the exhibit.

Cisco 200-301 image Question 661 110169 10072024004421000000

What is represented by the word "switch’’ in line 2 of the JSON schema?

Become a Premium Member for full access

Unlock Premium Member

Cisco 200-301 Practice Test 20

Question

Cisco 200-301 Practice Tests

Practice Tests