ExamGecko
Login
Home / F5 / 201 / List of questions
Ask Question

F5 201 Practice Test - Questions Answers, Page 22

Add to Whishlist

List of questions

Question 211

Report Export Collapse

When upgrading a BIG-IP redundant pair, what happens when one system has been updated but the other has not?

Become a Premium Member for full access
  Unlock Premium Member

Question 212

Report Export Collapse

When using the setup utility to configure a redundant pair, you are asked to provide a 'Failover Peer IP'. Which address is this?

Become a Premium Member for full access
  Unlock Premium Member

Question 213

Report Export Collapse

Which two statements describe differences between the active and standby systems? (Choose two.)

Become a Premium Member for full access
  Unlock Premium Member

Question 214

Report Export Collapse

Assuming other failover settings are at their default state, what would occur if the failover cable were to be disconnected for five seconds and then reconnected?

Become a Premium Member for full access
  Unlock Premium Member

Question 215

Report Export Collapse

Where is persistence mirroring configured?

Become a Premium Member for full access
  Unlock Premium Member

Question 216

Report Export Collapse

Given that VLAN failsafe is enabled on the external VLAN and the network that the active BIG-IP's external VLAN is connected to has failed, which statement is always true about the results?

Become a Premium Member for full access
  Unlock Premium Member

Question 217

Report Export Collapse

Where is connection mirroring configured?

Become a Premium Member for full access
  Unlock Premium Member

Question 218

Report Export Collapse

Assume the bigd daemon fails on the active system. Which three are possible results? (Choose three.)

Become a Premium Member for full access
  Unlock Premium Member

Question 219

Report Export Collapse

How is MAC masquerading configured?

Become a Premium Member for full access
  Unlock Premium Member

Question 220

Report Export Collapse

Which action will take place when a failover trigger is detected by the active system?

Become a Premium Member for full access
  Unlock Premium Member
Total 254 questions
Go to page: of 26
Open VPLUS File
Convert VPLUS to PDF

Related questions

A virtual server is defined using a source address based persistence profile. The last five connections were A, B, C, A, C . Given the conditions shown in the graphic, if a client with IP address 205.12.45.52 opens a connection to the virtual server, which member will be used for the connection?
A new BIG-IP VE is deployed with default settings. The BIG-IP Administrator completes the setup utility in the Configuration Utility. The internal self IP address fails to respond to a ping request. What is a possible cause of this issue?
A BIG-IP has a virtual server at 150.150.10.10:80 with SNAT automap configured. This BIG-IP also has a SNAT at 150.150.10.11 set for a source address range of 200.200.1.0 / 255.255.255.0. All other settings are at their default states. If a client with the IP address 200.200.1.1 sends a request to the virtual server, what is the source IP address when the associated packet is sent to the pool member?
A site wishes to perform source address translation on packets from some clients but not others. The determination is not based on the client's IP address, but on the virtual servers their packets arrive on. What could best accomplish this goal?
Refer to the exhibit. Why is the virtual server responsive to incoming connections?
Assume a BIG-IP has no NATs or SNATs configured. Which two scenarios are possible when client traffic arrives on a BIG-IP that is NOT destined to a self-IP? (Choose two.)
What should the BIG-IP Administrator do to apply and activate a hotfix to a BIG-IP device that is currently running version 11.0.0 on active partition HD1.1?
A virtual server is listening at 10.10.1.100:any and has the following iRule associated with it: when CLIENT_ACCEPTED { if {[TCP::local_port] equals 21 } { pool ftppool } elseif {[TCP::local_port] equals 23 } { pool telnetpool } If a user connects to 10.10.1.100 and port 22, which pool will receive the request?
Where is persistence mirroring configured?
Which statement is true concerning SSL termination?