Refer to the exhibit. A network administrator has developed a Python script on the local Linux machine and is trying to transfer it to the router. However, the transfer fails. Which action resolves this issue?

The SCP service must be enabled with the ip scp server enable command.

The SSH service must be enabled with the crypto key generate rsa command.

The SCP service must be enabled with the ip scp server enable command.

The Python interpreter must first be enabled with the guestshell enable command.

The SSH access must be allowed on the VTY lines using the transport input ssh command.

Refer to the exhibit. The network administrator can see the DHCP discovery packet in R1. but R2 is not replying to the DHCP request. The R1 related interface is configured with the DHCP helper address. If the PC is directly connected to the FaO/1 interface on R2, the DHCP server assigns as IP address from the DHCP pool to the PC. Which two commands resolve this issue? (Choose two.)

ip dhcp option 82 command on R2

service dhcp-relay command on R1

ip dhcp option 82 command on R2

ip dhcp relay information enable command on R1

ip dhcp relay information trust-all command on R2

Refer to the exhibit. An engineer configured BGP between routers R1 and R3 The BOP peers cannot establish neighbor adjacency to be able to exchange routes. Which configuration resofves this issue?

R3 router bgp 6502 address-family ipv6 neighbor AB01:2011:7:100::1 activate

R1 router bgp 6501 address-family ipv6 neighbor AB01:2011:7:100;:3 activate

R3 router bgp 6502 neighbor AB01:2011:7:100::1 ebgp-muttlhop 255

R1 router bgp 6501 neighborAB01:2011:7:100::3ebgp-multihop255

Refer to the exhibit. AS65510 iBGP is configured for directly connected neighbors. R4 cannot ping or traceroute network 192 168.100.0/24 Which action resolves this issue?

Configure R4 as a route reflector server and configure R1 as a route reflector client

Configure R1 as a route reflector server and configure R2 and R3 as route reflector clients

Configure R4 as a route reflector server and configure R2 and R3 as route reflector clients.

Configure R1 as a route reflector server and configure R4 as a route reflector client

Refer to the exhibit. BGP and EIGRP are mutually redistributed on R3, and EIGRP and OSPF are mutually redistributed on R1. Users report packet loss and interruption of service to applications hosted on the 10.1.1.0724 prefix. An engineer tested the link from R3 to R4 with no packet loss present but has noticed frequent routing changes on R3 when running the debug ip route command. Which action stabilizes the service?

Tag the 10.1.1.0/24 prefix and deny the prefix from being redistributed into OSPF on R1.

Repeat the test from R4 using ICMP ping on the local 10.1.1.0/24 prefix, and fix any Layer 2 errors on the host or switch side of the subnet. ^ C. Place an OSPF distribute-list outbound on R3 to block the 10.1.10/24 prefix from being advertised back to R3.

Reduce frequent OSPF SPF calculations on R3 that cause a high CPU and packet loss on traffic traversing R3.

Refer to the exhibit. A network administrator reviews the branch router console log to troubleshoot the OSPF adjacency issue with the DR router. Which action resolves this issue?

Configure matching hello and dead intervals between sites.

Advertise the branch WAN interface matching subnet for the DR site.

Configure matching hello and dead intervals between sites.

Configure the WAN interface for DR site in the related OSPF area.

Stabilize the DR site flapping link to establish OSPF adjacency.

Refer to the exhibit. Which action resolves the adjacency issue?

Configure the same autonomous system numbers.

Match the hello interval timers.

Configure the same EIGRP process IDs.

Configure the same autonomous system numbers.

A network administrator is trying to access a branch router using TACACS+ username and password credentials, but the administrator cannot log in to the router because the WAN connectivity is down.The branch router has following AAA configuration: Which command will resolve this problem when WAN connectivity is down?

aaa authentication login default group tacacs+ local

aaa authentication login default group tacacs+ enable

aaa authentication login default group tacacs+ console

aaa authentication login console group tacacs+ enable

Users report issues with reachability between areas as soon as an engineer configured summary routes between areas in a multiple area OSPF autonomous system. Which action resolves the issue?

Configure the area range command on the ASBR.

Configure the summary-address command on the ASBR.

Configure the summary-address command on the ABR.

Configure the area range command on the ABR.

Configure the area range command on the ASBR.

A network administrator is troubleshooting a high utilization issue on the route processor of a router that was reported by NMS The administrator logged into the router to check the control plane policing and observed that the BGP process is dropping a high number of routing packets and causing thousands of routes to recalculate frequently. Which solution resolves this issue?

Police the cir for BGP, conform-action transmit, and exceed action transmit.

Shape the pir for BGP, conform-action set-prec-transmit, and exceed action set-frde-transmit.

Shape the cir for BGP. conform-action transmit, and exceed action transmit.

Police the pir for BGP, conform-action set-prec-transmit, and exceed action set-clp-transmit.

Refer to the exhibit. When the FastEthemet0/1 goes down, the route to 172.29.0 0/16 via 192.168.253 2 is not installed in the RIB. Which action resolves the issue?

Configure feasible distance greater than the reported distance

Configure reported distance greater than the feasible distance

Configure feasible distance greater than the successor's feasible distance.

Configure reported distance greater than the successor's feasible distance.

Configure feasible distance greater than the reported distance

An engineer configured SNMP communities on the Core Sw1, but the SNMP server cannot obtain information from Core_Sw1.Which configuration resolves this issue?

access-list 20 permit 10.221.10.11

access-list 20 permit 10.221.10.12

snmp-server group NETVIEW v2c priv read NETVIEW access 20

snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22

access-list 20 permit 10.221.10.11

IPv6 is enabled in the infrastructure to support customers with an IPv6 network over WAN and to connect the head office to branch offices in the local network. One of the customers is already running IPv6 and wants to enable IPv6 over the DMVPN network infrastructure between the headend and branch sites. Which configuration command must be applied to establish an mGRE IPv6 tunnel neighborship?

tunnel mode gre multipoint ipv6

Refer to the exhibit. An engineer has configured policy-based routing and applied the configured to the correct interface.How is the configuration applied to the traffic that matches the access list?

It is forwarded using the routing table lookup.

How is VPN routing information distributed in an MPLS network?

It is controlled using of VPN target communities.

The top level of the customer data packet directs it to the correct CE device

It is established using VPN IPsec peers.

It is controlled using of VPN target communities.

It is controlled through the use of RD.

Refer to the exhibit. An engineer configured SNMP communities on the Core_SW1, but the SNMP server cannot obtain information from Core_SW1. Which configuration resolves this issue?

access-list 20 permit 10.221.10.11

snmp-server group NETVIEW v2c priv read NETVIEW access 20

access-list 20 permit 10.221.10.11

access-list 20 permit 10.221.10.12

snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22

What is a characteristic of Layer 3 MPLS VPNs?

Traffic engineering capabilities provide QoS and SLAs.

LSP signaling requires the use of unnumbered IP links for traffic engineering.

Traffic engineering supports multiple IGP instances

Traffic engineering capabilities provide QoS and SLAs.

Authentication is performed by using digital certificates or preshared keys.

Refer to the exhibit. An engineer configured IP SLA on R1 to avoid the ISP link flapping problem. but it is not working as designed IP SLA should wait 30 seconds before switching traffic to a secondary connection and then revert to the primary link after waning 20 seconds, when the primary link is available and stabilized.Which configuration resolves the issue?

R1(config)#track 700 ip sla 700R1(config-track)#delay down 30 up 20

R1(config)#ip sla 700R1(config-ip-sla)#delay down 30 up 20

R1(config)#ip sla 700R1(config-ip-sla)#delay down 20 up 30

R1(config)#track 700 ip sla 700R1(config-track)#delay down 30 up 20

R1(config)#track 700 ip sla 700R1(config-track)#delay down 20 up 30

Refer to the exhibit. A network administrator sets up an OSPF routing protocol for a DMVPN network on the hub router.Which configuration required to establish a DMVPN tunnel with multiple spokes?

ip ospf network point-to-multipoint on both spoke routers

ip ospf network point-to-point on the hub router

ip ospf network point-to-multipoint on One spoke router

ip ospf network point-to-point on both spoke routers

Refer to the exhibit. The Internet traffic should always prefer Site-A ISP-1 if the link and BGP connection are up; otherwise, all Internet traffic should go to ISP-2 Redistribution is configured between BGP and OSPF routing protocols and it is not working as expected. What action resolves the issue?

Set metric-type 1 at Site-A RTR1, and set metric-type 2 at Site-B RTR2

Set metric-type 2 at Site-A RTR1, and set metric-type 1 at Site-B RTR2

Set OSPF cost 100 at Site-A RTR1, and set OSPF Cost 200 at Site-B RTR2

Set OSPF cost 200 at Site: A RTR1 and set OSPF Cost 100 at Site-B RTR2

Set metric-type 1 at Site-A RTR1, and set metric-type 2 at Site-B RTR2

Refer to the exhibit. The AP status from Cisco DNA Center Assurance Dashboard shows some physical connectivity issues from access switch interface G1/0/14. Which command generates the diagnostic data to resolve the physical connectivity issues?

test cable diagnostics tdr interface GigabitEthernet1/0/14

Check cable-diagnostics tdr interface GigabitEthernet1/0/14

show cable-diagnostics tdr interface GigabitEthernet1/0/14

Verify cable-diagnostics tdr interface GigabitEthernet1/0/14

An engineer creates a Cisco DNA Center cluster with three nodes, but all the services are running on one host node. Which action resolves this issue?

Enable service distribution from the Systems 360 page.

Restore the link on the switch interface that is connected to a cluster link on the Cisco DNA Center

Click the master host node with all the services and select services to be moved to other hosts

Enable service distribution from the Systems 360 page.

Click system updates, and upgrade to the latest version of Cisco DNA Center.

R1 and R2 are configured as eBGP neighbor , R1 is in AS100 and R2 is in AS200. R2 is advertising these networks to R1:172.16.16.0/20172.16.3.0/24172.16.4.0/24192.168.1.0/24192.168.2.0/24172.16.0.0/16The network administrator on R1 must improve convergence by blocking all subnets of 172-16.0.0/16 major network with a mask lower than 23 from coming in, Which set of configurations accomplishes the task on R1?

ip prefix-list PL-1 deny 172.16.0.0/16 le 23ip prefix-list PL-1 permit 0.0.0.0/0 le 32!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 prefix-list PL-1 in

ip prefix-list PL-1 deny 172.16.0.0/16 ge 23ip prefix-list PL-1 permit 0.0.0.0/0 le 32!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 prefix-list PL-1 in

access-list 1 deny 172.16.0.0 0.0.254.255access-list 1 permit any!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 distribute-list 1 in

ip prefix-list PL-1 deny 172.16.0.0/16ip prefix-list PL-1 permit 0.0.0.0/0!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 prefix-list PL-1 in

The network administrator configured R1 to authenticate Telnet connections based on Cisco ISE using TACACS+. ISE has been configured with an IP address of 192.168.1.5 and with a network device pointing toward R1(192.168.1.1) with a shared secret password of Cisco123. The administrator cannot authenticate to R1 based on ISE. Which configuration fixes the issue?

line vty 0 4 login authentication telnet

ip tacacs-server host 192.168.1.5 key Cisco123

line vty 0 4 login authentication TAC-SERV

line vty 0 4 login authentication telnet

tacacs-server host 192.168.1.5 key Cisco123

Refer to the exhibit. A network administrator successfully logs in to a switch using SSH from a (RADIUS server When the network administrator uses a console port to access the switch the RADIUS server returns shell:privlvl= 15'' and the switch asks to enter the enable command \ the command is entered, it gets rejected.Which command set is used to troubleshoot and reserve this issue?

line con 0aaa authorization consoleauthorization exec!line vty 0 4transport input ssh

line con 0aaa authorization console!line vty 0 4authorization exec

line con 0aaa authorization console priv15!line vty 0 4authorization exec

line con 0aaa authorization consoleauthorization priv15!ine vty 0 4transport input ssh

Refer to the exhibit. The network administrator configured the network to connect two disjointed networks and ail the connectivity is up except the virtual link which causes area 250 to be unreachable. Which two configurations resolve this issue? (Choose two.)

R4router ospf 1no area 234 virtual-link 10.23.23.2area 234 virtual-link 0.0.0.22

R2router ospf 1no area 234 virtual-ink 10.34.34.4area 234 virtual-link 0.0.0.44

R4router ospf 1no area 234 virtual-link 10.23.23.2area 234 virtual-link 0.0.0.22

R4router ospf 1no area area 234 virtual-link 10.23.23.2area 0 virtual-link 0.0.0.22

R2router ospf 1no area area 234 virtual-link 10.34.34.4area 0 virtual-link 0.0.0.44

R2router ospf 1router-id 10.23.23.2

R2router ospf 1no area 234 virtual-ink 10.34.34.4area 234 virtual-link 0.0.0.44

Refer to the exhibit. R1 is configured with IP SLA to check the availability of the server behind R6 but it kept failing. Which configuration resolves the issue?

R6(config)# ip access-list extended DDOSR6(confg ext-nac)# 5 permit icmp host 10.10.10.1 host 10.66.66.66

R6(config)# ip sla responder udp-echo ip address 10.10.10.1 port 5000

R6(config)# ip access-list extended DDOSR6(config ext-nac)# 5 permit icmp host 10.66 66.66 host 10.10.10.1

R6(config)# ip access-list extended DDOSR6(confg ext-nac)# 5 permit icmp host 10.10.10.1 host 10.66.66.66

Cisco 300-410 Practice Test 6 - Free Online Exam Questions 201-240

Refer to the exhibit.

Cisco 300-410 image Question 201 111147 10072024005413000000

While troubleshooting an EIGRP neighbor adjacency problem, the network engineer notices that the interface connected to the neighboring router is not participating in the EIGRP process. Which action resolves the issues?

Become a Premium Member for full access

Unlock Premium Member

Cisco 300-410 Practice Test 6

Question

Drag and Drop

Hot Area

Cisco 300-410 Practice Tests

Practice Tests