Cisco 300-620 Practice Test - Questions Answers, Page 17
Question list
List of questions
Related questions
A network engineer must configure a new SNMP configuration and syslog servers. The requirement is for all faults and events related to endpoint groups, bridge domains, and VRFs to be sent to it.
Which action must be taken to meet the requirements?
Enable access monitoring policies on the required endpoint groups, bridge domains, and VRFs.
Utilize common tenant monitoring policies in the Cisco APIC.
Configure fabric monitoring policies and attach to the spine switch in the fabric.
Implement fabric-wide monitoring policies on all nodes.
An engineer must configure a Layer 3 connection to the WAN router. The hosts in production VRF must access WAN subnets. The engineer associates EPGs in the production VRF with the external routed domain. Which action completes the task?
Configure the Export Route Control Subnet scope for the external EPG.
Configure the External Subnets for the External EPG scope for the external EPG.
Configure the Import Route Control Subnet scope for the external EPG.
Configure the Shared Route Control Subnet scope for the external EPG.
Refer to the exhibit.
Refer to the exhibit. A Cisco APIC raises an error when the EPG must accept endpoints from a VMM domain created. Which action clears the fault?
Expand the VLAN pool for the VMM domain.
Create a bridge domain for the VMM domain.
Associate the EPG with the VMM domain.
Associate the VLAN pool with the VMM domain.
A Cisco ACI endpoint group must have its gateway address migrated out of the ACI fabric. An engineer configures EPG-TEST with a static port binding and configures the encap VLAN with the required VLAN. Which configuration set must be used on the bridge domain to meet these requirements?
L2 Unknown Unicast: Hardware Proxy
Unicast Routing: Disabled
ARP Flooding: Disabled
L2 Unknown Unicast: Flood
Unicast Routing: Disabled
ARP Flooding: Enabled
L2 Unknown Unicast: Flood
Unicast Routing: Enabled
ARP Flooding: Enabled
L2 Unknown Unicast: Hardware Proxy
Unicast Routing: Disabled
ARP Flooding: Enabled
What is a requirement for Cisco ACI IPN to manage multidestination traffic?
pervasive gateway
unicast routing
anycast gateway
multicast routing
An organization deploys active-active data centers and active-standby firewalls in each data center.
Which action should be taken in a Cisco ACI Multi-Pod to maintain traffic symmetry through the firewalls?
Disable Resilient Hashing.
Disable service node Health Tracking.
Enable Pod ID Aware Redirection.
Enable Endpoint Dataplane Learning.
Refer to the exhibit.
Refer to the exhibit. An engineer must allow IP mobility between Site1 and Site2 in a Cisco ACI Multi- Site orchestrator. The design must meet these requirements:
A disaster recovery (DR) solution must exist between the sites that do not require vMotion support.
The application must be started at a DR site without having to re-IP the application servers.
The solution must avoid any broadcast storms between the sites.
Which two actions meet these criteria? (Choose two.)
Define a unique bridge domain subnet per site.
Configure STP between Cisco ACI fabrics.
Deploy a local EPG for Site1 and Site2.
Disable Inter-site BUM Traffic.
Apply the L2 Stretch feature.
Refer to the exhibit.
Refer to the exhibit. New e-commerce software is deployed on Cisco ACI fabric. The environment must meet these requirements:
The overall number of contracts must be reduced by reusing the existing contracts within a VRF when possible.
The e-commerce software must communicate only with software EPGs that are part of the same ANP.
The e-commerce software must be prevented from communicating with applications in different ANPs.
Which scope must be selected to meet these requirements?
Application Profile
Endpoint Group
Tenant
Global
Refer to the exhibit.
Refer to the exhibit. A company merges three of its departments: CORP, HR, and SERVICES, Currently, the connectivity between departments is achieved by using VRF route leaking. The requirement is to redesign the Cisco ACI networking architecture to communicate between EPGs and BDs from any tenant without configuring contracts or VRF route leaking. Which configuration meets these criteria?
Configure an unenforced VRF in the user tenant and map all required EPGs to it.
Implement an enforced VRF in the common tenant and map all required BDs to it.
Configure an enforced VRF in the user tenant and map all required EPGs to it.
Implement an unenforced VRF in the common tenant and map all required BDs to it.
What two actions should be taken to deploy a new Cisco ACI Multi-Pod setup? (Choose two.)
Configure MP-BGP on IPN routers that face the Cisco ACI spines.
Connect all spines to the IPN.
Configure anycast RP for the underlying multicast protocol
Configure the TEP pool of the new pod to be routable across the IPN.
Increase interface MTU for all IPN routers to support VXLAN traffic.
Question