Refer to the exhibit: After implementing a new design for the network, a technician reviews the pictured CLI output as part of the MOP.Which two statements describe what the technician can ascertain from the ImpNull output? (Choose two.)

Penultimate Hop Popping is in use for the prefix displayed

Label 3 is in use for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10

Label 0 is used for the prefix displayed but will not be part of the MPLS label stack for packets destined for 192 168.10.10.

Ultimate Hop Popping is in use for the prefix displayed.

Label 0 is used for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10

Penultimate Hop Popping is in use for the prefix displayed

Label 3 is in use for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10

Refer to the exhibit: In which way does router R1 operate differently than router R2?

R1 sends LSA types 1 and 2, while R2 sends type 1. 2. and 7 LSAs

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs

R1 sends LSA types 1 and 2, while R2 sends type 1. 2. and 7 LSAs

R1 sends LSA type 2 only and R2 sends LSA type 1 only

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs

A network engineer must enable the helper router to terminate the OSPF graceful restart process if it detects any changes in the LSA. Which command enables this feature?

nsf ietf helper strict-lsa-checking

Refer to the exhibit: A network engineer is implementing an OSPF configuration Based on the output, which statement is true?

OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0

In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.

OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0

OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.

IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway

Refer to the exhibit: Assume all other configurations are correct and the network is otherwise operating normally. Which conclusion can you draw about the neighbor relationship between routers R1 and R2?

The neighbor relationship is down because R1 believes R2 is in AS 65012.

The neighbor relationship will be up only if the two devices have activated the correct neighbor relationships under the IPv4 address family

The neighbor relationship is down because R1 believes R2 is in AS 65012.

The neighbor relationship is up

The neighbor relationship is down because the loco I-as value for R2 is missing in the R1 neighbor statement

Which statement about the Cisco MPLS TE forwarding adjacency feature is true?

It enables the Cisco MPLS TE tunnel to be advertised into the running IGP.

It enables the headend and tailend routers to establish a bidirectional tunnel

It enables the tailend router to advertise routes to the headend router over the tunnel

It enables the MPLS core to use EIGRP as the routing protocol

It enables the Cisco MPLS TE tunnel to be advertised into the running IGP.

Refer to the exhibit: R1 is connected to two service providers and is under a DDoS attack Which statement about this design is true if uRPF in strict mode is configured on both interfaces'?

R1 drops all traffic that ingresses either interface that has a FIB entry that exits a different interface

R1 accepts source addresses on interface gigabitethernet0/1 that are private addresses

R1 permits asymmetric routing as long as the AS-RATH attribute entry matches the connected AS

R1 drops destination addresses that are routed to a null interface on the router

R1 drops all traffic that ingresses either interface that has a FIB entry that exits a different interface

A router is configured to perform MPLS LDP graceful restart.Which three steps are included when the RP sends an LDP initialization to a neighbor to establish an LDP session? (Choose three)

Learn from Network (L.) flage, set to 1

Learn from Neighbor (N) flag, set to 1

Graceful restart capability in OPEN message

Learn from Network (L.) flage, set to 1

Refer to the exhibit: Which statement describes the effect of this configuration?

It matches HTTP traffic for use in a policy map

It applies a service policy to all interfaces remarking HTTP traffic

It creates an ACL named WEB that filters HTTP traffic.

It matches HTTP traffic for use in a policy map

It modifies the default policy map to allow all HTTP traffic through the router

Why do Cisco MPLS TE tunnels require a link-state routing protocol?

The tunnel endpoints can use the link-state database to evaluate the entire topology and determine the best path

Link-state routing protocols use SPF calculations that the tunnel endpoints leverage to implement the tunnel

The link-state database provides a data repository from which the tunnel endpoints can dynamically select a source ID

The tunnel endpoints can use the link-state database to evaluate the entire topology and determine the best path

The link state database provides segmentation by area, which improves the path-selection process

Which additional feature does MPLS DiffServ tunneling support?

interaction between MPLS and IGP

using GRE tunnels to hide markings

Refer to the exhibit: Which statement supports QPPB implementation?

QoS policies rely exclusively on BGP attributes to manipulate traffic

QoS policies are identified in the MPLS forwarding table

QoS policies rely exclusively on BGP attributes to manipulate traffic

QoS policies use BGP to gain full coverage on the network.

QPPB policies affect only egress traffic

Refer to the exhibit: What does the REST API command do?

It executes the commands specified in Descriptions xml

It retrieves the information requested by Descriptions xml

It removes the information identified by Descriptions xml

It executes the commands specified in Descriptions xml

It displays the information identified by Descriptions xml

Why do packet loops occur during the configuration of BlDlR-PIM?

The network is partially upgraded to support BIDlR-PIM

The network does not support BIDIR-PIM

The network is partially upgraded to support BIDlR-PIM

No interface for carrying traffic for multicast groups has been configured

The router has not been configured to advertise itself

Refer to the exhibit: This output is included at the end of an output that was provided by a device using NETCONF.What does the code show?

It shows NETCONF uses remote procedure calls.

It shows the hostname of the device as rpc-reply

It shows that the running configuration is blank

It shows NETCONF uses remote procedure calls.

It shows that the full configuration is being modeled by VANG

Refer to the exhibit: What is the URL used for with REST API?

It is used to send a message to the APIC to perform an operation on a managed object or class operator

It is used to contact a URL filter to determine the efficacy of a web address

It is used to send a TACACS+ authentication request to a server

It is used to send a message to the APIC to perform an operation on a managed object or class operator

It is used to initiate an FTP session to save a running configuration of a device.

You are configuring MPLS traffic-engineering tunnels in the core.Which two ways exist for the tunnel path across the core? (Choose two )

Tunnel links inherit IGP metrics by default unless overridden

Tunnels can be configured with dynamic path or explicitly defined path

Tunnel links inherit IGP metrics by default unless overridden

Tunnels can be configured with dynamic path or explicitly defined path

A zero bandwidth tunnel is not a valid option

The bandwidth statement creates a "hard" reservation on the link-The dynamic path option is supported only with IS-IS

When configuring traffic engineering tunnels in Cisco MPLS core network, you see the traffic is not taking the expected path in the core.Which command do you use to quickly check path of a TE tunnel?

Traceroute mpls ipv4 -tunnel destination

show mpls traffic-engineering tunnels

traceroute <tunnel destination IP>

Refer to the exhibit: P3 and PE4 are at the edge of the service provider core and serve as ABR routers Aggregation areas are on either side of the core.Which statement about the architecture is true?

If each area is running its own IGP. BGP must provide an end-to-end MPLS LSP

If each area is running its own IGP. the ABR routers must redistribute the IGP routing table into BGP

To support seamless MPLS. TDP must be used as the label protocol

If each area is running its own IGP. BGP must provide an end-to-end MPLS LSP

To support seamless MPLS, the BGP route reflector feature must be disabled

Refer to the exhibit: Which statement about this configuration is true"?

It is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing

It requires an explicit Cisco MPLS TE path to be configured for the tunnel to run

It requires OSPF to also be running to have optimized Cisco MPLS TE tunnels

It requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run

It is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing

You are testing the capabilities of MPLS OAM ping.Which statement is true?

An LSP is not required for the reply to reach the ingress MPLS router

MPLS OAM ping works solely with Cisco MPLS TE

MPLS OAM ping works solely with P2P LSPs

An LSP breakage results in the ingress MPLS router never receiving any reply

An LSP is not required for the reply to reach the ingress MPLS router

Refer to the exhibit: A network administrator wants to enhance the security for SNMP for this configuration.Which action can the network administrator implement?

Re-configure to use SNMPv2 with MD5 authentication

Add a community string to the existing entry

Maintain the configuration but switch to an encrypted password for device access through SSH

Refer to the exhibit: Which effect of this configuration is true?

R1 can support a peer that is configured for LDP SSO/NSF as the peer recovers from an outage

R1 can failover only to a peer that is configured for LDP SSO/NSF

R1 can support a graceful restart operation on the peer, even if graceful restart is disabled on the peer

A customer of an ISP requests support to setup a BGP routing policy. Which BGP attribute should be configured to choose specific BGP speakers as preferred exit points for the customer AS?

lowest local preference inbound

highest local preference outbound

lowest local preference inbound

highest local preference inbound

lowest multi-exit discriminator

Refer to the exhibit: Router 1 was experiencing a DDoS attack that was traced to interface gjgabitethernet0/1.Which statement about this configuration is true?

Router 1 accepts source addresses that have a match in the FIB that indicates it is reachable through a real interface

Router 1 drops all traffic that ingresses interface gigabitethernet0/1 that has a FIB entry that exits a different interface

Router 1 accepts source addresses on interface gigabitethemet0/1 that are private addresses

Router 1 accepts all traffic that ingresses and egresses interface gigabitethernet0/1

Router 1 accepts source addresses that have a match in the FIB that indicates it is reachable through a real interface

Refer to the exhibit: What is significant about the number 2 in the configuration?

It is the numeric name of the ACL that contains the list of SNMP managers with access to the agent

It dictates the number of sessions that can be open with the SNMP manager

It indicates two SNMP managers can read and write with the agent using community string cisco test

It represents the version of SNMP running

A regional MPLS VPN provider operates m two regions and wants to provide MPLS L 3VPN service for a customer with two sites in these separate locations. The VPN provider approaches another organization to provide backbone carrier services so that the provider can connect to these two locations.Which statement about this scenario is true?

When eBGP is used for label exchange using the send label option, MPLS-BGP forwarding is configured under the global ABC CSC PE-to CE interface

When edge routers at different regional sites are connected over the global carrier backbone, MPeBGP must run between the routers to exchange the customer VPNv4 routes

When eBGP is used for label exchange using the send label option, MPLS-BGP forwarding is configured under the global ABC CSC PE-to CE interface

When IGP is used for route exchange and LDP for label exchange, MPLS is enabled only on the VRF interface on the backbone-earner PE side.

When BGP is used for both route and label exchange, the neighbor a.b.c.d send-lable command is used under the address family VPNv4 command mode.

What is the difference between SNMP and model-driven telemetry?

Telemetry allows for modeled network data to be pushed to the network administrator on an asneeded basis

Telemetry uses traps and inform messages to deliver data to a network administrator on a polling basis

SNMP uses the YANG data modeling language

SNMP pushes network data to the network administrator whenever it is queried

Refer to the exhibit: An engineer is preparing to implement data plane security configuration.Which statement about this configuration is true?

All traffic to 192.168.1.0/24 is dropped

Router 1 drops all traffic with a local-preference set to 150

All traffic to 192.168.1.0/24 is dropped

Router 1 and Router 2 advertise the route to 192.0.2.0/24 to all BGFD peers.

Cisco 350-501 Practice Test 2 - Free Online Exam Prep & Questions

Question 1 / 40

Refer to the exhibit:

Cisco 350-501 image Question 41 116323 10102024233011000000

An engineer is preparing to implement link aggregation configuration.

Which statement al about this configuration is true?

The switch port actively sends packets to negotiate an EtherChannel using PAgP

The switch port accepts LACP and PAgP packets from a connected peer and negotiate an EtherChannel using the common EtherChannel mode.

The switch port passively negotiates an EtherChannel if it receives PAgP packets from a connected peer

The switch port negotiates an EtherChannel if it receives LACP packets from a connected peer

Comment (0)

Cisco 350-501 Practice Test 2

Question

Cisco 350-501 Practice Tests

Practice Tests