What Is the primary role of Ansible In a network?

It is used as a network automation provisioning and configuration tool.

It is used as a debugging tool for connectivity issues between the DMZ and an enterprise intranet.

It Is used to diagnose Layer 11ssues In data centers that span more than one city block.

It is used to deploy IPv6 configuration is networks That are dual slack.

It is used as a network automation provisioning and configuration tool.

A network team has failed to implement IS-IS multitopology. What is the reason for it?

The routing process did not support extended metrics.

The router did not support VRFs.

The routing process did not support extended metrics.

The router did not have Cisco Discovery Protocol and Cisco Express Forwarding disabled.

The routing process supported Level 1 only.

Refer to the exhibit. A network engineer is implementing OSPF multiare a. Which command on interface GO/1 resolves adjacency issues in the new area?

ip ospf network point-to-multipoint

A network engineer is implementing BFD configuration changes on a customer's equipment. How is the bfd interval configuration on the interface disconnected?

It is automatically disconnected when the BFD main interface is removed.

The status of the interface changes.

The IPv4 or IPv6 address configuration on the interface changes.

It is automatically disconnected when the BFD-configured subinterface is removed.

It is automatically disconnected when the BFD main interface is removed.

An engineer is trying to implement BGP in a multihomed architecture. What must the engineer configure to influence inbound path selection?

A route map with AS_PATH attribute to control the inbound traffic.

A route map with WEIGHT attribute to control the inbound traffic.

An offset list to set the metric for routes received from neighboring autonomous systems.

An access list to identify traffic and enable it on both of the provider-facing interfaces.

A route map with AS_PATH attribute to control the inbound traffic.

Refer to the exhibit. What type of configuration is it?

It is configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing.

It is configuration that requires an explicit Cisco MPLS TE path to be configured for the tunnel to run.

It is configuration that requires OSPF to also be running to have optimized Cisco MPLS TE tunnels.

It is configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing.

It is configuration that requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run.

Refer to the exhibit. An engineer configured multicast routing on client's network. What is the effect of this multicast implementation?

R2 is unable to share information because the ip pirn autorp listener command is missing.

R2 floods information about R1 throughout the multicast domain.

R2 is unable to share information because the ip pirn autorp listener command is missing.

R1 floods information about R2 throughout the multicast domain.

R2 is elected as the RP for this domain.

Refer to the exhibit. An engineer is updating this network to meet these conditions:• Area 10 will receive inter-area routes and support mutual redistribution of external routes with the extranet.• The ::/0 route is prohibited in Area 10.• Area 11 will receive only the ::/0 route from the ABR.• External route redistribution is not supported in Area 11.• The ABR in Area 11 will advertise no interarea routes.Which two configurations must be performed to meet the requirements? (Choose two.)

Configure area 11 as stub no-summary on R7 and as stub on XR31.

Configure area 10 as nssa on R9 and XR32.

Configure area 11 as nssa no-summary on R7 and as nssa on XR31.

Configure area 10 as stub on R9 and XR32.

Configure area 11 as stub no-summary on R7 and as stub on XR31.

Configure area 11 as nssa default-information-originate on R7 and as nssa on XR31.

Configure area 10 as nssa on R9 and XR32.

Refer to the exhibit. An engineer needs to implement this QoS policy on customer's network due to ongoing slow network issues. What will be the effect on the network when the engineer implements this configuration?

Traffic that is identified in the ciscotest class map will be marked with IP precedence 1 when it exits the poso/2/0/0 interface.

Traffic that is identified in the ciscotest class map will be remarked from IP precedence 1 to DSCP AF11 when it enters the pos0/2/0/0 interface.

Traffic that is identified in the ciscopolicy class map will be marked with IP precedence 1 when it enters the pos0/2/0/0 interface.

Traffic that is identified in the ciscopolicy class map will be remarked from IP precedence 1 to DSCP AF11 when it exits the pos0/2/0/0 interface.

Traffic that is identified in the ciscotest class map will be marked with IP precedence 1 when it exits the poso/2/0/0 interface.

While implementing TTL security, an engineer issues the PE(config-router-af)#neighbor 2.2.2.2 ttlsecurity hops 2 command. After issuing this command, which BGP packets does the PE accept?

from 2.2.2.2, with a TTL of 253 or more

from 2.2.2.2, with a TTL of less than 2

to 2.2.2.2, with a TTL of less than 253

from 2.2.2.2, with a TTL of 253 or more

to 2.2.2.2, with a TTL of 2 or more

A network engineer is configuring a router to send multicast traffic for the 239.10.10.10 group.Which configuration must an .... forward the traffic?

Cisco(config)# interface ethernet 1/0 Cisco(config-if)# ip igmp join-group 239.10.10.10

Cisco(config)# interface ethernet 1/0 Cisco(config-if)# ip igmp max-groups action replace

Cisco(config)# interface ethernet 1/0 Cisco(config-if)# ip igmp filter

Cisco(config)# interface ethernet 1/0 Cisco(config-if)# ip igmp access-group 239.10.10.10

Cisco(config)# interface ethernet 1/0 Cisco(config-if)# ip igmp join-group 239.10.10.10

BGP has been implemented on a IOS XR router. Which configuration sends BGP IPv4 labels to build inter-domain LSPs?

router bgp 65515 neighbor 172.16.70.23 address-family ipv4 labeled-unicast

router bgp 65515 address-family ipv4 unicast neighbor 172.16.70.23 send-community extended

router bgp 65515 no bgp default ipv4-unicast

router bgp 65515 address-family ipv4 unicast neighbor 172.16.70.23 send-community

router bgp 65515 neighbor 172.16.70.23 address-family ipv4 labeled-unicast

Which module refers to the network automation using Ansible?

the iosxr_command module to issue run commands on remote devices

the iosxr_system module to collect facts from remote devices

the iosxr_user module to manage banners for users in the local database

the losxr_logging module to run debugging for seventy levels 2 to 5

the iosxr_command module to issue run commands on remote devices

What is the characteristic of the Tl-LFA?

It guarantees a loop-free path for all interfaces in the OSPf- super backbone .

It applies on each area and instance and makes all the interfaces inherit the configuration

It guarantees a loop-free path for all areas configured m OSPF

It applies only on the instance and makes at the interfaces inherit the configuration

Refer to the exhibit. An engineer began to configure LDP between R1 and R2, but R1 and R2 cannot yet establish an LDP TCP connection. Which additional task must be completed to finish the implementation?

Configure the mpls Idp neighbor 172.16.0.1 password command on R1

Configure the mpls Idp neighbor 10.0.12.1 password command on R1

Configure the no mpls Idp password option 1 command on R2

Configure the no mpls Idp password option 1 command on R1

Refer to me exhibit. A network operator recently configured BGP FlowSpec for me internal IT network What will be inferred from the configuration deployed on me network?

The policy is configured locally on CSRl and drops all traffic for TCP ports 80 and 443

The policy is learned via BGP FlowSpec and drops all traffic for TCP ports 80 and 443

The policy is warned via BC FlowSpec aid has active traffic

The policy is configured locally on CSR1 and currently has no active traffic

Refer to the exhibit. A network operator needs to shut down interface Gi0/0/0/2 for maintenance. What occurs to the interface states of Gi0/0/0/0 and Gi0/0/0/1?

Gi0/0/0/1 becomes active Gi0/0/0/0 remains standby

Gi0/0/0/1 and Gi0/0/0/0 become active

Gi0/0/0/1 and Gi0//0/0 remains standby

Gi0/0/0/0 becomes active. Gi0/00/1 remains standby

Gi0/0/0/1 becomes active Gi0/0/0/0 remains standby

The administrator of a small company network notices that intermittent network issues occasionally cause inbound notifications to its SNMP servers to be lost. Which configuration must the administrator apply so that the SNMP servers acknowledge the notifications that they receive?

snmp-server enable traps bgp snmp-server host 192.169.2.1 Informs

snmp-server community ciscotest rw 10

snmp-server host tests.cisco.com public snmp-server community ciscotest rw 10

snmp-server enable traps bgp snmp-server host 192.169.2.1 Informs

What are two characteristics of MPLS TE turrets? (Choose two)

They use RSVP to provide bandwidth for the tunnel.

They require EIGRP to be running in the core.

They use RSVP to provide bandwidth for the tunnel.

They are run over Ethernet cores only.

The headend and tailend routes of the tunnel must have a BGP relationship

Refer to the exhibit. An engineer applied a gRPC dial-in configuration on customer's router to provide connection multiplexing and two-way streaming. What does this configuration accomplish in a gRPC?

It is the encoding requested by the gRPC server.

IT is the encoding that is used for dial-in and dial-out.

It is used for encoding with the default protocol buffers

It is the encoding requested by the gRPC client.

What are two factors to consider when implementing NSR High Availability on an MPLS PE router?(Choose two.)

It consumes more memory and CPU resources than NSF

It operates normally without NSR support on the PE peers.

It consumes more memory and CPU resources than NSF

It operates normally without NSR support on the PE peers.

It requires all PE-CE sessions to support NSR

It requires routing protocol extensions

It cannot sync state information across redundant RPs

Refer to the exhibit. A network engineer is deploying SNMP configuration on client's routers. Encrypted authentication must be included on router 1 to provide security and protect message confidentially. Which action should the engineer perform on the routers to accomplish this task?

snmp-server user testuser group 1 remote 192.168.0.254 v3 auth md5 testpassword

snmp-server host 192.168.0.254 informs version 3 auth testuser config.

snmp-server user testuser group 1 remote 192.168.0.254 v3 auth md5 testpassword

snmp-server group group 1 v3 auth.

An engineer needs to implement QOS mechanism on customer's network as some applications going over the internet are slower than others. Which two actions must the engineer perform when implementing traffic shaping on the network in order to accomplish this task? (Choose two)

Configure a queue with sufficient memory to buffer excess packets.

Implement a scheduling function to handle delayed packets.

Configure a queue with sufficient memory to buffer excess packets.

Configure the token values in bytes.

Implement packet remarking for excess traffic.

Implement a scheduling function to handle delayed packets.

Configure a threshold over which excess packets are discarded.

Refer to the exhibit. What does the script configure?

selectors for the in-band management

Which two actions describe ISP delegation to PCE servers? (Choose two)

adding a new PCE server with lower precedence than the primary PCE

removing TE re-optimization timer timeouts

adding a new PCE server with lower precedence than the primary PCE

changing the precedence of any of the PCE servers

removing TE re-optimization timer timeouts

entering the mpls traffic-eng reoptimize command

adding a new PCE server with higher precedence than the primary PCE

Refer to the exhibit. ASN 64501 currently reaches the networks under the 10.0.0.0/8 prefix via the North_B router, which is a slow backup link. The administrator of ASN 64502 wants traffic from ASN 64501 to 10.0.0.0/8 to travel via the primary link North_

Set a Lower Weight value for incoming traffic on North_A

Which change to the network configuration accomplishes this task?

Set a higher local preference between North_A and South_A

Advertise the 10.0.0.0/8 prefix through North_B and specific subnets through North_A

Set a Lower Weight value for incoming traffic on North_A

Set a lower MED between North_B and South_B

Refer to the exhibit. While troubleshooting a connectivity issue on router R2, a network engineer with an employee id:3876.13.497 notices that although it detects three OSPF links from R1, the OSPF prefixes are missing from the routing table. What is the reason for the problem?

The R2 Serial 1/0 interface is configured with an IP address, but the R1 Serial R1 Serial 1/0 interface in unnumbered.

The serial interfaces have different MTUs

Both loopback interfaces on R1 are configured as stub

The R2 Serial 1/0 interface is configured with an IP address, but the R1 Serial R1 Serial 1/0 interface in unnumbered.

The subnet masks on the serial interfaces are mismatched.

Which statement about TLS is accurate when using RESTCONF to write configurations on network devices'?

It requires certificates for authentication.

It is provided using NGINX acting as a proxy web server

It is used for HTTP and HTTPS requests.

It is not supported on Cisco devices

Cisco 350-501 Practice Test 4 - Free Online Exam Questions 121-160

Spam

Selling illegal goods, money scams etc.

Hate Speech

Serious attack on a group.

Harassment and bullying

Harassing an individual (including doxing)

Harmful activities

Threatening or glorifying violence or serious harm, including self-harm

Adult content (Consensual)

Nudity/Sexual content

Sexual exploitation and abuse (child safety)

Sexually explicit or suggestive imagery or writing involving minors

Sexual exploitation and abuse (adults and animals)

Sexually explicit or suggestive imagery or writing involving non-consenting adults or non-humans

Plagiarism

Reusing content without attribution (link and blockquotes)

Poorly written

Not in English or has very bad formatting, grammar, and spelling

Inappropriate credential

Author's credential is offensive, spam, or impersonation

Other

Ex. Illegal content, incomplete question...

Cisco 350-501 Practice Test 4

Question

Cisco 350-501 Practice Tests

Practice Tests