ExamGecko
Login
Home / Cisco / 300-510 / List of questions
Ask Question

Cisco 300-510 Practice Test - Questions Answers, Page 7

Add to Whishlist

List of questions

Question 61

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 61 63879133849451671685937

Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3. Which action corrects the problem?

Become a Premium Member for full access
  Unlock Premium Member

Question 62

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 62 63879133849451671685937

A network operator is troubleshooting TE tunnels and discovers that the soft preemption is not working as desired. Where should the soft preemption be applied to solve the issue?

Become a Premium Member for full access
  Unlock Premium Member

Question 63

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 63 6387913384946729642300

What is the relationship between Router 1 and Router 2?

Become a Premium Member for full access
  Unlock Premium Member

Question 64

Report Export Collapse

Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Software?

Become a Premium Member for full access
  Unlock Premium Member

Question 65

Report Export Collapse

What is the purpose of a BGP confederation?

Become a Premium Member for full access
  Unlock Premium Member

Question 66

Report Export Collapse

What is the characteristic of enabling segment routing for IGPs?

Become a Premium Member for full access
  Unlock Premium Member

Question 67

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 67 6387913384946729642300

While configuring router 2 with all the default values, a network engineer cannot see any route received in router 1. How should the engineer solve the issue?

Become a Premium Member for full access
  Unlock Premium Member

Question 68

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 68 6387913384946729642300

An engineer has configured all routers in the environment to run IS-IS Level 1 and Level 2 routing. The engineer wants traffic from R1 to R5 to pass via R2. but IS-IS routing has calculated the best path via R4. Which action corrects the problem?

Become a Premium Member for full access
  Unlock Premium Member

Question 69

Report Export Collapse

What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)

Become a Premium Member for full access
  Unlock Premium Member

Question 70

Report Export Collapse

Which expression, when used with the as-path-set command, matches the AS path attribute of the route?

Become a Premium Member for full access
  Unlock Premium Member
Total 269 questions
Go to page: of 27
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. The service provider deployed segment routing in its core P2 is connected to P3 and P4 via a point-to-multipoint link as shown The service provider provides connectivity for a large enterprise with three main offices in different geographic regions Each office is connected via one of the three PEs The enterprise wants to implement multicast traffic across the service provider to stream mission-critical applications between sites The applications will be sourced from a server connected to the network through PE2 Which action must the network-engineering team take so that multicast traffic will flow between the enterprise sites over the point-to-multipoint link?
The engineering team at ISP_1 must improve network stability time and minimize the impact of routing instabilities from other domains to unicast transit services in the backbone R1 is part of an OSPF- enabled network, and acts as an ASBR connected via interface GiO/1 to the external domain The OSPF exponential backoff algorithm RFC 3623 with helper mode is already implemented on R1 Which additional configuration must the ISP_1 team apply to suppress routing instability for 3 minutes'?
Refer to the exhibit. A network engineer at a large ISP with an employee ID 4876 94 052 started to configure OSPF on two routers The engineer notices that router 1 learned about network 20 20 20 0/24 from router 2, but router 2 did not learn about 10.10 10.0/24 from router 1 Layer 2 and Layer 3 connectivity are working between the two routers and the physical connection between the devices is functioning. Which action must the engineer take to resolve the issue?
Which BGP well-known attributes are preserved between peers with a BGP confederation?
Which fact must a network architect consider when implementing IGMP in a multicast routing environment?
RPL has several fundamental capabilities that differ from those present in configurations oriented to traditional route maps Routing policy language introduces the notion of sets Which group of set types is valid in RPL?
What are two major differences between OSPF and IS-IS routing protocols? (Choose two.)
Refer to the exhibit. Early in the growth cycle of a small enterprise the network-engineering team implemented segment routing to support automation of the IPv4 network As the network grew organically more devices were added and the company migrated to SRv6 The company is now planning to significantly expand the number of hosts connected to R2 and R6 which will require further path manipulation Which action must the team take to customize the route that traffic takes between endpoints in the network?
Refer to the exhibit. EBGP peering is up between BGP AS 65101 and BGP AS 65201 The service provider expects traffic convergence within 300ms between the two autonomous systems but the network operations team sees that route and traffic convergence is too slow Which two actions improve the convergence time? (Choose two.)
Refer to the exhibit. AJI four routers on the network reside in the same data center The four routers are running IS-IS between them in Level 1 mode within an IPv4 network After a network engineer installed several new servers connected to R4, users connected via R1 reported they could not connect to applications on the servers The engineer has determined that R4 is receiving routes from R3 but it is failing to receive routes from R1 Which action must the engineer take to resolve the issue?