Huawei H12-351_V1.0 Practice Test - Questions Answers, Page 5

ATP stands for Acceptance Test Plan, which is a document that needs to be output after the low level design is complete. The ATP describes the acceptance criteria and test cases for the project.

Reference: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/atp

Customer Requirement Specification (CRS) is a document that needs to be output after the project requirements are clarified. The CRS describes the customer's requirements in detail and serves as the basis for subsequent project design and delivery.

Reference: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/crs

Only: All statements are true about the WLAN site survey in different typical scenarios.

Reference: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/wlan-sitesurvey

When calculating the number of APs, you cannot simply divide the total required bandwidth by the maximum bandwidth of a single AP. You also need to consider other factors such as signal coverage area, user density, interference level, and application type.

Reference: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/calculationof-the-number-of-aps

B is false because generally, a STA roams when it detects that the signal strength is less than -70 dBm or -65 dBm, not -75 dBm.

Reference: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/wlanroaming-and-signal-strength

According to the Huawei documents and resources, the troubleshooting operations for the AP onboarding failures are as follows:

APS fail to be authenticated by the WAC: Whitelist the APS. The WAC can authenticate APs based on their MAC addresses or SNs. If an AP is not whitelisted on the WAC, it cannot be authenticated and onboarded.

License resources on the WAC are insufficient: Expand the license capacity. The WAC can manage a limited number of APs based on its license. If the license resources are insufficient, some APs cannot be onboarded.

APS fail to obtain IP addresses: Check the DHCP server. The APs need to obtain IP addresses from a DHCP server before they can communicate with the WAC. If the DHCP server is not configured or reachable, the APs cannot obtain IP addresses and onboard.

APS fail to ping the WAC: Check the network between the WAC and APS. The APs need to ping the WAC to discover its IP address and establish a CAPWAP tunnel. If there is a network problem between the WAC and APs, such as incorrect VLAN configuration or firewall blocking, the APs cannot ping the WAC and onboard.

Therefore, APS fail to be authenticated by the WAC - c, License resources on the WAC are insufficient

- b, APS fail to obtain IP addresses - d, APS fail to ping the WAC - a is the correct answer. Reference: :

https://support.huawei.com/enterprise/en/doc/EDOC1100158948/9a0d5c37/ap-onboardingfailures

C is false because HTTPS redirection is not required for Portal authentication to work properly.

Reference:

https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/troubleshootingportal-authentication-failures

B is false because disabling radio 1 of APs does not affect the Internet connection speed of STAs that use radio 2.

Reference:

https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/troubleshooting-slowinternet-connection

When a STA roams from AP1 to AP2 at Layer 2, AP2 notifies its neighbors of the MAC address learned from this STA. The MAC address is not encapsulated in a tunnel and sent to AP1 for forwarding.

Instead, AP1 deletes the MAC address entry of the STA and releases the IP address lease.

Reference: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/layer-2-roaming