ExamGecko
Home Home / Huawei / H31-311

Huawei H31-311 Practice Test - Questions Answers, Page 17

Question list
Search
Search

Which of the following statements about overhead bytes is incorrect?

A.
A1 and A2 are framing bytes. These bytes are used to separate STM-1 frames in a signal flow.
A.
A1 and A2 are framing bytes. These bytes are used to separate STM-1 frames in a signal flow.
Answers
B.
J0 is a regenerator section trace byte. This byte is used to repeatedly transmit a section access point identifier, so that the receive end can verify its continuous connection to the specified transmit end.
B.
J0 is a regenerator section trace byte. This byte is used to repeatedly transmit a section access point identifier, so that the receive end can verify its continuous connection to the specified transmit end.
Answers
C.
B1 is bit interleaved parity-8 (BIP-8). This byte is used to monitor bit errors at the regenerator section layer.
C.
B1 is bit interleaved parity-8 (BIP-8). This byte is used to monitor bit errors at the regenerator section layer.
Answers
D.
E1 and E2 are orderwire bytes. These bytes are used to provide a voice channel for orderwire connections.
D.
E1 and E2 are orderwire bytes. These bytes are used to provide a voice channel for orderwire connections.
Answers
Suggested answer: A

Which of the following factors determines that the optical signal-to-noise ratio (OSNR) at the receive end decreases to a certain extent After signals are transmitted for a certain distance in a WDM system, the optical signal-to-noise ratio (OSNR) at the receive end decreases to a certain extent. Which of the following is the main cause?

A.
EDFAs are used.
A.
EDFAs are used.
Answers
B.
Multiplexers and demultiplexers are used.
B.
Multiplexers and demultiplexers are used.
Answers
C.
New types of optical fibers are not used.
C.
New types of optical fibers are not used.
Answers
D.
Fiber attenuation is excessively high.
D.
Fiber attenuation is excessively high.
Answers
Suggested answer: A

Which of the following methods can be used to multiplex lower-order ODUk to higher-order ODUk?

A.
Time division multiplexing
A.
Time division multiplexing
Answers
B.
Wavelength division multiplexing
B.
Wavelength division multiplexing
Answers
C.
Space division multiplexing
C.
Space division multiplexing
Answers
D.
Frequency division multiplexing
D.
Frequency division multiplexing
Answers
Suggested answer: A

When the transmit end detects that the b6-b8 of the K2 byte is 110, it indicates that the () alarm is reported at the transmit end.

A.
MS-AIS
A.
MS-AIS
Answers
B.
R-LOS
B.
R-LOS
Answers
C.
R-LOF
C.
R-LOF
Answers
D.
MS-RDI
D.
MS-RDI
Answers
Suggested answer: A, B, C

A PAUSE frame uses a reserved multicast address and is not forwarded by a bridge or switch, In this way, the PAUSE frame does not generate any additional information.

A.
TRUE
A.
TRUE
Answers
B.
FALSE
B.
FALSE
Answers
Suggested answer: A

The backplane has two -48 V power supply cables, and each board obtains two -48 V power supplies from the backplane. After the power supplies are combined by diodes, various voltages required by each component are obtained through the DC/DC power module and linear conversion.

A.
TRUE
A.
TRUE
Answers
B.
FALSE
B.
FALSE
Answers
Suggested answer: A

For the (local) HA solution where the active and standby servers are deployed in the same place, which of the following platforms can be deployed? (Multiple Choice)

A.
Windows
A.
Windows
Answers
B.
Solaris
B.
Solaris
Answers
C.
SUSE Linux
C.
SUSE Linux
Answers
D.
All of the above
D.
All of the above
Answers
Suggested answer: B, C

Which of the following is the basic requirement of a DWDM system on a light source?

A.
The output wavelength is stable.
A.
The output wavelength is stable.
Answers
B.
The direct modulation method is used.
B.
The direct modulation method is used.
Answers
C.
The dispersion tolerance is low.
C.
The dispersion tolerance is low.
Answers
D.
The transmit power is high.
D.
The transmit power is high.
Answers
Suggested answer: A

Which of the following statements about the definition of SDH is correct?

A.
A complete standard digital signal hierarchy that provides synchronous digital transmission, multiplexing, and cross-connection
A.
A complete standard digital signal hierarchy that provides synchronous digital transmission, multiplexing, and cross-connection
Answers
B.
A hierarchy of standardized digital signals that can be asynchronously multiplexed
B.
A hierarchy of standardized digital signals that can be asynchronously multiplexed
Answers
C.
A hierarchy of standardized digital signals that can be asynchronously cross-connected
C.
A hierarchy of standardized digital signals that can be asynchronously cross-connected
Answers
D.
A hierarchy that can be used for asynchronous digital transmission
D.
A hierarchy that can be used for asynchronous digital transmission
Answers
Suggested answer: A

The rate of STM-1 is () bit/s.

A.
9*270*4*8000
A.
9*270*4*8000
Answers
B.
9*270*1*8000*16
B.
9*270*1*8000*16
Answers
C.
9*270*1*8000*8
C.
9*270*1*8000*8
Answers
D.
9*270*1*8000
D.
9*270*1*8000
Answers
Suggested answer: C
Total 186 questions
Go to page: of 19