Home / Huawei / H35-260

Huawei H35-260 Practice Test - Questions Answers

Question list

List of questions

Question 1

(0)

According to the IEEE 802JQ standard, where is the VLAN ID field on the Ethernet?

Question 2

(0)

What are the reasons for the R-Los alarm reported on the 0TU board?

Question 3

(0)

Which of the following light source technologies does the 100GOTU board use?

Question 4

(0)

The 802.1Q tag header contains a two-byte TPID. Which of the following is its standard value?

Question 5

(0)

Both the 1310nm and 1550nm transmission windows are low-loss windows. In the DWDM system, only the 1550nm transmission window is used. Which of the following options is the main reason?

Question 6

(0)

Which of the following alarms will be reported by the peer end when it is detected that the error code exceeds the limit in the B2 byte?

Question 7

(0)

In the CES service, which of the descriptions of "packet loading time" and "jitter buffer time" is wrong?

Question 8

(0)

DCM optical power debugging requires the input of DCM to be no greater than which of the following values?

Question 9

(0)

The DWDM system has extremely high requirements on the stability of the light source. Which of the following factors will affect the stability of the light source?

Question 10

(0)

The EDFA erbium-doped fiber amplifier is a key component of the new generation of optical fiber systems. Which of the following options are correct for the description of its advantages?

Question 1

According to the IEEE 802JQ standard, where is the VLAN ID field on the Ethernet?

Before source MAC address and destination MAC address

Between the source MAC address and the destination MAC address

After the source MA dog address and the destination MAC address

not fixed

Show Answer Comment (0)

Question 2

What are the reasons for the R-Los alarm reported on the 0TU board?

The local optical port is not used

The local laser is turned off, resulting in no optical signal input

Broken fiber or line performance degradation

The receiving board at the local end is faulty, and the line receiving fails

Show Answer Comment (0)

Question 3

Which of the following light source technologies does the 100GOTU board use?

Direct modulation light source

Light source of EA modulation method

MZ modulation light source

Coherent reception modulation mode light source

Show Answer Comment (0)

Question 4

The 802.1Q tag header contains a two-byte TPID. Which of the following is its standard value?

8100

8847

8147

88A8

Show Answer Comment (0)

Question 5

Both the 1310nm and 1550nm transmission windows are low-loss windows. In the DWDM system, only the 1550nm transmission window is used. Which of the following options is the main reason?

EDFA operating wavelength flat region includes this window

Small nonlinear effects in the 1550nm wavelength region

1550nm wavelength region is suitable for long distance transmission

1550nm window loss is smaller than 1310nm window

Show Answer Comment (0)

Question 6

Which of the following alarms will be reported by the peer end when it is detected that the error code exceeds the limit in the B2 byte?

MS-AIS

RS-BBE

MS-REI

MS-BBE

Show Answer Comment (0)

Question 7

In the CES service, which of the descriptions of "packet loading time" and "jitter buffer time" is wrong?

The jitter buffer time represents the size of the buffer

Packet loading time refers to the length of time for PW packets to load TDM frames

Packet loading time, the configuration of NEs at both ends must be the same

The value of the packet loading time cannot be less than the jitter buffer time

Show Answer Comment (0)

Question 8

DCM optical power debugging requires the input of DCM to be no greater than which of the following values?

-2

-3

-4

-5

Translated from Chinese (Simplified) to English - www.onlinedoctranslator.com

Show Answer Comment (0)

Question 9

The DWDM system has extremely high requirements on the stability of the light source. Which of the following factors will affect the stability of the light source?

Temperature

Drive Current

Packaging

Humidity

Show Answer Comment (0)

Question 10

The EDFA erbium-doped fiber amplifier is a key component of the new generation of optical fiber systems. Which of the following options are correct for the description of its advantages?

High gain

High output power

The working wavelength is consistent with the minimum attenuation window of single-mode fiber

Low noise figure

Gain Flattening

Show Answer Comment (0)

Total 338 questions