Home / HP / HPE0-S60

HP HPE0-S60 Practice Test - Questions Answers, Page 2

Question list

List of questions

Question 11

(0)

Your customer has the following HPE Synergy setup - 3 HPE Synergy 12000 Frames - 4 HPE Virtual Connect SE 100 Gb F32 Modules - 2 HPE Synergy 50 GO Interconnect Link Modules - 36 HPE Synergy 480

Question 12

(0)

Which statement about HPE Superdome Flex 280 is true?

Question 13

(0)

You are troubleshooting an HPE OneView server profile that presents a critical state. The server profile was configured with a Link Aggregation Group What should you check to fix the issue?

Question 14

(0)

Your customer experienced some problems caused by outdated HPE Superdome Flex firmware. Which update method should they use to avoid these issues in the future?

Question 15

(0)

Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE

Question 16

(0)

Your customer has me following HPE Synergy setup - Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure - Two HPE V

Question 17

(0)

Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute

Question 18

(0)

Refer to the exhibit. Which statement about this logical interconnect group is true?

Question 19

(0)

Your customer plans to add four HPE Synergy frames to an existing management ring Ail installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM mod

Question 20

(0)

You plan to configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXI system. What is required from the VMware side to enable LAG?

Related questions

Your customer plans to deploy VMware ESXi 7. 0 U2, and they are looking for a hardware platform that will allow them to use up to 16 CPU sockets Which HPE compute system meets the customer requirements?

Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric. The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They also plan a vSAN deployment leveraging HPE D3940 Storage Modules and SSD drives The customer requested the following components: - HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules - Two HPE Virtual Connect SE 100Gb F32 Modules for Synergy - An appropriate number of vSAN Standard licenses for each compute node - One HPE O3940 Storage Module with 40 SSDs - All required cables and options Which statement about this request is true?

Which statement about a new HPE SimpliVity deployment is true?

You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter. Which storage object should you check using SSMC to verify whether vVol datastore is configured property?

Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?

Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames How will this change impact the customer environment?

You plan to configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXI system. What is required from the VMware side to enable LAG?

Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory. Which HPE compute system meets this customer's requirements?

Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex 280 They plan to manage new components using HPE OneView What must be done to achieve this goal?

Question 11

Your customer has the following HPE Synergy setup

- 3 HPE Synergy 12000 Frames

- 4 HPE Virtual Connect SE 100 Gb F32 Modules

- 2 HPE Synergy 50 GO Interconnect Link Modules

- 36 HPE Synergy 480 Gen10 Plus compute modules

- 2 HPE Composer 2 modules

Which statement about this setup is true?

To use all compute nodes, the customer must create at least two logical enclosures

To manage all frames, the customer must buy two additional HPE Composer 2 modules

The customer must buy 36 HPE OneView Advanced licenses to manage compute modules

The customer can add one D3940 storage Module to each of the frames

Show Answer Comment (0)

Question 12

Which statement about HPE Superdome Flex 280 is true?

It supports 2 to 8 sockets in 2-socket increments.

it cannot be managed using HPE OneView.

It must be equipped with at least 768 GB of memory.

It can support up to two nPars with an external RMC.

Show Answer Comment (0)

Question 13

You are troubleshooting an HPE OneView server profile that presents a critical state. The server profile was configured with a Link Aggregation Group What should you check to fix the issue?

if both FiexNICs are configured with the same speed

If the logical enclosure is built on at least three HPE Synergy frames

if both FiexNICs are connected to different networks

if the logical enclosure is configured with redundant master modules

Show Answer Comment (0)

Question 14

Your customer experienced some problems caused by outdated HPE Superdome Flex firmware.

Which update method should they use to avoid these issues in the future?

HPE OneView method for I/O firmware update procedure

RMC CLI to update I/O and HPE Persistent Memory firmware

HPE OneView IT HPE Persistent Memory firmware must be updated.

HPE SUM if HPE Persistent Memory firmware must be updated

Show Answer Comment (0)

Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE OneView.

What must the customer do before migrating the application?

Migrate the application to a Logical JBOD and connect it to the new server

Copy the server profile and assign the clone to the new hardware

Edit the server profile and change server hardware type

Create a new server profile template and apply to the new hardware

Show Answer Comment (0)

Question 16

Your customer has me following HPE Synergy setup

- Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure

- Two HPE Virtual Connect SE 100Gb F32 Module for Synergy

- Four HPE Synergy 50Gb interconnect Link Module

- Six HPE Synergy Virtual Connect SE 32Gb FC Modules

The customer needs to add a frame.

Which statement about the expansion of this setup is true?

The additional frame must have HPE Virtual Connect FC modules installed

The customer can grow the existing logical enclosure up to 5 frames

The customer has to create a new logical enclosure for the additional frame

The additional frame cannot have 12Gb SAS connection modules installed

Show Answer Comment (0)

Question 17

Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute modules. HPE ProLiant

Gen 10 servers and an MSA array.

Which statement about compatibility of the existing environment with the planned software components is true?

Both HPE Synergy Gen10 full-height compute module plugins will require a license

HPE OneView for VMware vCenter Server does not support standalone HPE ProLiant servers

To use the required plugins HPE ProLiant Gen10 systems must be managed using HPE OneView

HPE Storage integration Pack for VMware vCenter does not support MSA arrays

Show Answer Comment (0)

Question 18

Refer to the exhibit.

Which statement about this logical interconnect group is true?

Both modules are located in different frames for redundancy

For an uplink set, ports from different modules can be selected

interconnect modules are installed in interconnect bays 1 and 4

An additional license is required to change the enclosure count

Show Answer Comment (0)

Question 19

Your customer plans to add four HPE Synergy frames to an existing management ring Ail installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM modules.

Which statement about mixing different FLM modules is true?

Existing 2-port FLM modules must be replaced with 4-port FLM modules

A management ring can contain mixed frame link module configurations

A management ring with mixed FLM modules cannot have more than 12 frames

Mixing different FLM modules is allowed if all of them have the same firmware version

Show Answer Comment (0)