Home / HP / HPE0-S60

HP HPE0-S60 Practice Test - Questions Answers, Page 5

Question list

List of questions

Question 41

(0)

Your customer reports mat an external FC boot volume for Windows server is visible four times in the Disk Management 1 online and 3 offline. What should you do to resolve this issue?

Question 42

(0)

Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options - SAS connectivity installed in the first fabric - FC connectivity Ins

Question 43

(0)

Your customer wants to add a second HPE Synergy frame to an existing logical enclosure Based on a single HPE Synergy frame. The customer wants to use a highly available master setup. Which procedur

Question 44

(0)

In the past a customer experienced a networking issue where network ports went down and came back up in quick succession. Which HPE Virtual Connect SE 100 GD F32 Module for HPE Synergy feature can

Question 45

(0)

Which tool can be used to evaluate me health of an HPE Oneview appliance before proceeding with an appliance updated.

Question 46

(0)

Your customer wants to compare HPE Superdome Flex with HPE Superdome Flex 280. Which statement about these two systems is true?

Question 47

(0)

Your customer plans to deploy HPE Superdome Flex and configure two nPars, each based on two chassis Which components must be included in the proposal to meet the customer's needs?

Question 48

(0)

Refer to the exhibit. Which statement about this logical JBOD is true?

Question 49

(0)

Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wan

Question 50

(0)

Your customer plans to deploy VMware vSAN using D3940 Storage Modules. Which statement about this solution is true?

Related questions

Your customer plans to deploy VMware ESXi 7. 0 U2, and they are looking for a hardware platform that will allow them to use up to 16 CPU sockets Which HPE compute system meets the customer requirements?

Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric. The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They also plan a vSAN deployment leveraging HPE D3940 Storage Modules and SSD drives The customer requested the following components: - HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules - Two HPE Virtual Connect SE 100Gb F32 Modules for Synergy - An appropriate number of vSAN Standard licenses for each compute node - One HPE O3940 Storage Module with 40 SSDs - All required cables and options Which statement about this request is true?

Which statement about a new HPE SimpliVity deployment is true?

Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames How will this change impact the customer environment?

You plan to configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXI system. What is required from the VMware side to enable LAG?

You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter. Which storage object should you check using SSMC to verify whether vVol datastore is configured property?

Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?

Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory. Which HPE compute system meets this customer's requirements?

Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex 280 They plan to manage new components using HPE OneView What must be done to achieve this goal?

Question 41

Your customer reports mat an external FC boot volume for Windows server is visible four times in the Disk Management 1 online and 3 offline.

What should you do to resolve this issue?

Disable deduplication for this volume at the array level

Remove the offline disks using array management tools

Install and configure MPIO on me Windows system

Remove the offline disks using Windows Disk Management

Show Answer Comment (0)

Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options - SAS connectivity installed in the first fabric - FC connectivity Installed In the second fabric - Ethernet connectivity installed in the third fabric.

Which statement regarding this setup is true?

Each compute node must have at least 768GB of memory installed

Interconnect modules that provide SAS connectivity should be moved to the third fabric

Each interconnect module in each fabric must be properly licensed in HPE OneView

Compute nodes must have a second CPU installed to access the second fabric.

Show Answer Comment (0)

Question 43

Your customer wants to add a second HPE Synergy frame to an existing logical enclosure Based on a single HPE Synergy frame. The customer wants to use a highly available master setup.

Which procedures should De performed during the expansion process? (Select two.)

Create a new logical interconnect group and enclosure group for two frames setup

Create a new logical enclosure based on both HPE Synergy frames.

Re-parent an existing enclosure group to the new logical interconnect group.

Modify an existing logical interconnect to include second HPE Synergy frame.

Move one of the master modules to the appropriate interconnect bay in the second frame.

Show Answer Comment (0)

Question 44

In the past a customer experienced a networking issue where network ports went down and came back up in quick succession.

Which HPE Virtual Connect SE 100 GD F32 Module for HPE Synergy feature can be configured to disable such ports?

Pause flood protection

sFlow

Storm control

Port flap protection

Show Answer Comment (0)

Question 45

Which tool can be used to evaluate me health of an HPE Oneview appliance before proceeding with an appliance updated.

HPE Composer Maintenance Console

HPE OneView Update Readiness Checker

HPE OneView Global Dashboard

HPE OneView Firmware Compliance Report

Show Answer Comment (0)

Question 46

Your customer wants to compare HPE Superdome Flex with HPE Superdome Flex 280.

Which statement about these two systems is true?

Only HPE Superdome Rex 280 can be managed using HPE OneView

Only HPE Superdome Flex supports HPE Persistent Memory

Only HPE Superdome Flex 280 can support multiple nPars

Only HPE Superdome Flex supports 32 sockets and 48TB of memory

Show Answer Comment (0)

Question 47

Your customer plans to deploy HPE Superdome Flex and configure two nPars, each based on two chassis Which components must be included in the proposal to meet the customer's needs?

Rack Management Controller for nPar management

HPE Superdome Flex Grid licenses enabling connectivity between chassis

At least Tour HPE Persistent Memory DIMMs per nPar

One base chassis and three expansion chassis with licenses

Show Answer Comment (0)

Question 48

Refer to the exhibit.

Which statement about this logical JBOD is true?

This logical JBOD can be connected to multiple systems to formulate a snared datastore.

After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created

After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done

This logical JBOD can be presented to the compute nodes in a different frame.

Show Answer Comment (0)

Question 49

Enable FC primary and secondary boot on the modules through the HPE OneView interface

FC connectivity on the modules should be enabled through the service console by disabling FCoE.

Add FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules

Enter both modules into a maintenance mode, then enable FC connectivity through CLI

Show Answer Comment (0)

Question 50

Your customer plans to deploy VMware vSAN using D3940 Storage Modules.

Which statement about this solution is true?

The 12Gb SAS modules required for D3940 connectivity can only be installed in the first fabric.

To use the storage controller that will access D3940 storage modules, a second CPU must be installed.

For VMware vSAN deployment, all drives in the D3940 storage modules must be SSD drives.

All drives in the D3940 storage modules must formulate a single logical drive with RAID5 configured

Show Answer Comment (0)

Total 78 questions

3 4 5 6 7

Go to page: of 8