HP HPE2-T37 Practice Test - Questions Answers, Page 2
Question list
List of questions
Related questions
Refer to the exhibit.
Your customer wants to define a Logical Interconnect Group (UG) and set the redundancy of the master modules to highly available, but this option is not available. What is a possible reason?
There are not sufficient frames for highly available setup.
Some master modules only support a redundant setup.
Firmware on the master modules is too low to support highly available setup.
A dedicated license must be added to HPE OneView to enable this feature.
You try to add an HPE Primera array to HPE OneView, but you get a connectivity error. However, you can connect to the array using SSMC. What should you verify before adding HPE Primera to HPE OneView?
whether WSAPI service is enabled on HPE Primera array.
whether the appropriate license for HPE Primera Is available in HPE OneView.
whether array management using HPE OneView is enabled in SSMC.
whether there are at least two Fibre Channel networks defined in HPE OneView.
Your customer asks you if it is possible to perform HPE Synergy initial setup remotely. How should you respond?
Remote HPE Synergy setup is possible if HPE Composer 2 is used and a DHCP server Is available in the management network.
Remote HPE Synergy Installation can be done only if an additional set of the services was purchased together with hardware platform.
HPE Synergy cannot be deployed remotely, as Initial setup must be performed using a local console connection.
HPE Synergy can be configured remotely through a secure connection to the FLM if this option was enabled In the factory.
You ate implementing an HPE Synergy solution with multiple frames in one management ring. Image Streamer is not a part of this solution. How can an IPv4 address pool defined by the administrator be used In HPE OneView?
to provide static IP addresses to IL0 and interconnect modules if applicable
to provide static IP addresses for an operating system running on a Compute Module
to provide static IP addresses for Logical Interconnects and Logical Enclosures
to provide static IP addresses for storage systems managed in HPE OneView
You want to add the latest IL0 firmware to an HPE OneView firmware repository. How can you complete this task?
A PowerShell script must be used to upload IL0 firmware to the Internal or external firmware repository.
A custom SPP iso Image must be created with the new IL0 firmware version and uploaded to the repository.
An external repository must be created, because standalone components are supported only In an external repository.
ILO firmware can be marked as a hotnx and uploaded directly to the Internal or external firmware repository.
Your customer plans to use HPE OneView to manage a small environment based on HPE ProLiant servers that includes G7 and Gen 10 systems. What should you explain to this customer?
HPE Management Agent must he installed for HPE ProLiant Gen 10 servers.
HPE ProLiant G7 and Gen10 cannot be managed using the same appliance.
Not all of the features will be available for HPE ProLiant G7 systems.
HPE ProLiant Gen 10 servers do not need an HPE OneView license.
What is the best practice when deploying an HPE OneView appliance?
Enable VMware Fault Tolerance if the appliance is deployed to a VMware hypervisor.
deploy the appliance in a hypervisor cluster that Is not managed by OneView.
Use thin-provisioning for the HPE OneView appliance to save storage capacity.
Deploy two HPE OneView appliances and configure them in HA mode.
After replacing a failed Compute Module, you notice the server profile Is not automatically assigned to the replaced server hardware. What can cause this issue?
IL0 firmware of the replacement server is different than firmware in broken server.
Server profile affinity is configured to Device Day + server hardware.
The enclosure group has to be updated to match the original enclosure group.
The replacement server has more memory or CPUs than broken machine.
What is a network set?
It is a collection of all internal networks defined for a specific type of traffic like vSAN or vMotion.
It is a collection of untagged Ethernet networks that form a named group to simplify server profile creation.
It is a collection of tagged Ethernet networks that form a named group to simplify server profile creation.
It is a collection of all networks configured within HPE OneView regardless of network type.
You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?
The sFlow option must be enabled and configured.
Both FlexNlCs must be connected to the same network.
The Compute Module profile must have exactly two connections defined.
An upgrade license must be purchased and deployed.
Question