Exhibit You are attempting to summarize routes from the 203.0.113.128/25 IP block on R8 to AS 64500. You implement the export policy shown in the exhibit and all routes from the routing table stop being advertised.In this scenario, which two steps would you take to summarize the route in BGP? (Choose two.)

Add the set routing-options static route 203.0.113.123/25 discard command.

Replace exact in the export policy with orlonger.

Remove the from protocol bgp command from the export policy.

Add the set protocols bgp family inet unicast add-path command to allow additional routes to the RIB tables. -

Add the set routing-options static route 203.0.113.123/25 discard command.

Replace exact in the export policy with orlonger.

Which two statements are correct about VPLS tunnels? (Choose two.)

LDP-signaled VPLS tunnels only support control bit 0.

BGP-signaled VPLS tunnels can use either RSVP or LDP between the PE routers.

LDP-signaled VPLS tunnels only support control bit 0.

LDP-signaled VPLS tunnels use auto-discovery to provision sites

BGP-signaled VPLS tunnels can use either RSVP or LDP between the PE routers.

BGP-signaled VPLS tunnels require manual provisioning of sites.

Exhibit CE-1 must advertise ten subnets to PE-1 using BGP Once CE-1 starts advertising the subnets to PE-1, the BGP peering state changes to Active.Referring to the CLI output shown in the exhibit, which statement is correct?

CE-1 is configured with an incorrect peer AS

CE-1 is advertising its entire routing table.

CE-1 is configured with an incorrect peer AS

The prefix limit has been reached on PE-1

Exhibit Referring to the exhibit, which two statements are true? (Choose two.)

The device advertising this route into EVPN is 192.168.101.5.

This route is learned through EBGP

The device advertising this route into EVPN is 192.168.101.5.

The devices advertising this route into EVPN are 10 0 2 12 and 10.0.2.22.

What is the correct order of packet flow through configurable components in the Junos OS CoS features?

Behavior Aggregate Classifier -> Input Policer -> Multifield Classifier -> Forwarding Policy Options -> Fabric Scheduler -> Output Policer -> Scheduler/Shaper/RED -> Rewrite Marker

Multifield Classifier -> Behavior Aggregate Classifier -> Input Policer -> Forwarding Policy Options -> Fabric Scheduler -> Output Policer -> Rewrite Marker -> Scheduler/Shaper/RED

Behavior Aggregate Classifier -> Multifield Classifier -> Input Policer -> Forwarding Policy Options -> Fabric Scheduler -> Output Policer -> Scheduler/Shaper/RED -> Rewrite Marker

Behavior Aggregate Classifier -> Input Policer -> Multifield Classifier -> Forwarding Policy Options -> Fabric Scheduler -> Output Policer -> Scheduler/Shaper/RED -> Rewrite Marker

Behavior Aggregate Classifier -> Multifield Classifier -> Input Policer -> Forwarding Policy Options -> Fabric Scheduler -> Scheduler/Shaper/RED -> Output Policer -> Rewrite Marker

When building an interprovider VPN, you notice on the PE router that you have hidden routes which are received from your BGP peer with family inet labeled-unica3t configured.Which parameter must you configure to solve this problem?

Under the family inet labeled-unicast hierarchy, add the resolve-vpn parameter.

Under the family inet labeled-unicast hierarchy, add the explicit null parameter.

Under the protocols ospf hierarchy, add the traffic-engineering parameter.

Under the family inet labeled-unicast hierarchy, add the resolve-vpn parameter.

Under the protocols mpls hierarchy, add the traffic-engineering parameter

You are configuring a BGP signaled Layer 2 VPN across your MPLS enabled core network. In this scenario, which statement is correct?

This type of VPN requires the support of the inet-vpn NLRI on all core BGP devices

You must assign a unique site number to each attached site's configuration.

This type of VPN only supports Ethernet interfaces when connecting to CE devices.

This type of VPN requires the support of the inet-vpn NLRI on all core BGP devices

You must use the same route-distinguiaher value on both PE devices.

Which two statements are correct about the customer interface in an LDP-signaled pseudowire? (Choose two)

When the encapsulation is vLan-ccc or extended-vlan-ccc, the configured VLAN tag is included in the control plane LDP advertisement

When the encapsulation is ethemet-ccc, tagged and untagged frames are both accepted in the data plane.

When the encapsulation is vlan-ccc or extended-vlan-ccc, the configured VLAN tag is not included in the control plane LDP advertisement

When the encapsulation is ethernet-ccc, only frames without a VLAN tag are accepted in the data plane

When the encapsulation is vLan-ccc or extended-vlan-ccc, the configured VLAN tag is included in the control plane LDP advertisement

When the encapsulation is ethemet-ccc, tagged and untagged frames are both accepted in the data plane.

Exhibit Referring to the exhibit, which statement is true?

The 10.101.1.0/24 route will be shared if the auto-export parameter is configured

The 10.101.1.0/24 route will be shared if the vrf-table-label parameter is configured.

The 10.101.1.0/24 route will only be shared if BGP is configured in the routing instance

The 10.101.1 0/24 route will be shared if there are other VRFs that use the same route target community

The 10.101.1.0/24 route will be shared if the auto-export parameter is configured

Exhibit Referring to the exhibit, what do the brackets [ ] in the AS path identify?

They identify an AS set, which are groups of AS numbers in which the order does not matter

They identify the local AS number associated with the AS path if configured on the router, or if AS path prepending is configured

They identify an AS set, which are groups of AS numbers in which the order does not matter

They identify that the autonomous system number is incomplete and awaiting more information from the BGP protocol.

They identify that a BGP confederation is being used to ensure that there are no routing loops.

When using OSPFv3 for an IPv4 environment, which statement is correct?

OSPFv3 supports IPv4 only on interfaces with family inet6 defined

OSPFv3 supports both IPv6 and IPv4, but not in the same routing instance.

OSPFv3 is not backward compatible with IPv4

OSPFv3 supports IPv4 only on interfaces with family inet6 defined

Which two statements are correct about reflecting inet-vpn unicast prefixes in BGP route reflection? (Choose two.)

Route reflectors do not change any existing BGP attributes by default when advertising routes.

A BGP peer does not require any configuration changes to become a route reflector client.

Route reflectors do not change any existing BGP attributes by default when advertising routes.

A BGP peer does not require any configuration changes to become a route reflector client.

Clients add their originator ID when advertising routes to their route reflector

Route reflectors add their cluster ID to the AS path when readvertising client routes.

Exhibit You are examining an L3VPN route that includes the information shown in the exhibitWhich statement is correct in this scenario?

The information shows a Type 1 route distinguisher.

The information shows a Type 0 route distinguisher

The information shows a Type 2 route distinguisher.

The information shows a route target

Exhibit Referring to the exhibit, you must provide Internet access for VPN-A using CE-1 as the hub CE.Which two statements are correct in this situation? (Choose two.)

You must use RIB groups to leak routes between the inet. o and vpn-a. inet. o tables.

Internet traffic from Site 2 takes the path of PE-2 -> PE-1 -> CE-1 -> PE-1 -> GW-1.

You must use RIB groups to leak routes between the inet. o and vpn-a. inet. o tables.

RIB groups are not needed to leak routes between the inet. 0 and VPN---A. inet. 0 tables,

Internet traffic from Site 2 takes the path of PE-2 -> PE-1 -> GW-1.

Internet traffic from Site 2 takes the path of PE-2 -> PE-1 -> CE-1 -> PE-1 -> GW-1.

Exhibit The network shown in the exhibit is based on IS-ISWhich statement is correct in this scenario?

The NSEL byte for Area 0001 is 00.

The routers are using unnumbered interfaces

The system IDofR1_2 is 192.168.16.1

Exhibit Based on the configuration contents shown in the exhibit, which statement is true?

Joins for group 224.7.7.7 are accepted if the group count is less than 25

Joins for group 224.7.7.7 are rejected if the source address is 192.168.100.10

Joins for any group are accepted if the group count value is less than 25.

Joins for group 224.7.7.7 are always rejected, regardless of the group count.

Joins for group 224.7.7.7 are accepted if the group count is less than 25

Which two statements are correct regarding bootstrap messages that are forwarded within a PIM sparse mode domain? (Choose two.)

Bootstrap messages distribute RP information dynamically during an RP election.

Bootstrap messages are forwarded to all routers within a PIM sparse-mode domain.

Bootstrap messages are forwarded only to routers that explicitly requested the messages within the PIM sparse-mode domain

Bootstrap messages distribute RP information dynamically during an RP election.

Bootstrap messages are used to notify which router is the PIM RP

Bootstrap messages are forwarded to all routers within a PIM sparse-mode domain.

Exhibit Which two statements about the configuration shown in the exhibit are correct? (Choose two.)

This VPN connects customer sites that use different AS numbers.

This VPN connects customer sites that use the same AS number

Which two statements about IS-IS are correct? (Choose two.)

CSNPs are flooded periodically.

PSNPs contain only descriptions of LSPs.

CSNPs are flooded periodically.

PSNPs are flooded periodically.

PSNPs contain only descriptions of LSPs.

CSNPs contain only descriptions of LSPs.

Exhibit Referring to the exhibit, which statement is correct?

The route-distinguisher configuration will allow overlapping routes to be shared between CE-1 and CE-2.

The vrf-target configuration will allow routes to be shared between CE-1 and CE-2.

The vrf-target configuration will stop routes from being shared between CE-1 and CE-2.

The route-distinguisher configuration will allow overlapping routes to be shared between CE-1 and CE-2.

The route-diatinguisher configuration will stop routes from being shared between CE-1 and CE-2.

Exhibit Click the Exhibit button-Referring to the exhibit, which two statements are correct about BGP routes on R3 that are learned from the ISP-A neighbor? (Choose two.)

By default, the next-hop value for these routes is not changed by ISP-A before being sent to R3.

The BGP local-preference value that is used by ISP-A is not advertised to R3.

By default, the next-hop value for these routes is not changed by ISP-A before being sent to R3.

The BGP local-preference value that is used by ISP-A is not advertised to R3.

All BGP attribute values must be removed before receiving the routes.

The next-hop value for these routes is changed by ISP-A before being sent to R3.

Exhibit You have MAC addresses moving in your EVPN environmentReferring to the exhibit, which two statements are correct about the sequence number? (Choose two)

It resolves conflicting MAC address ownership claims.

It helps the local PE to identify the latest advertisement.

It identifies MAC addresses that should be discarded.

It resolves conflicting MAC address ownership claims.

It helps the local PE to identify the latest advertisement.

It is advertised using a Type 2 message

Exhibit R2 is receiving the same route from R1 and R3. You must ensure that you can load balance traffic for that route.Referring to the exhibit, which configuration change will allow load balancing?

Configure the multipath multiple-as parameter under the global BGP configuration.

Configure the multipath parameter under the global BGP configuration.

Apply the prepend policy as an import policy under group R1.

Configure the multipath multiple-as parameter under the global BGP configuration.

Apply the prepend policy as an import policy under group R3.

Exhibit You are troubleshooting the connection between AS 64496 and AS 64497 and notice that only one of the paths is being used for traffic forwarding.Referring to the exhibit, which three actions will ensure that R1 is configured properly for load balancing BGP routes? (Choose three.)

Verify that the routing table on R1 has BGP routes for 203.0.113.128/25 with multiple next hops.

Verify that the multipath option is configured under protocols bgp on both R2 and R3.

Verify that the multipath option is configured under protocols bgp on R1.

Verify that the routing table on R1 has BGP routes for 203.0.113.128/25 with multiple next hops.

Verify that the multipath option is configured under protocols bgp on both R2 and R3.

Verify that there is a load balancing export policy under routing-options for the received BGP routes on R1.

Verify that the multipath option is configured under protocols bgp on R1.

Verify that an import load balancing policy exists under protocols bgp for the received BGP routes on R1.

You are configuring anycast RP for load balancing and redundancy in your PIM-SM domain. You want to share active sources between RPs.In this scenario, what are two solutions that will accomplish this task? (Choose two.)

Configure MSDP on each RP router.

Configure anycast PIM with the rp-set statement on each RP router.

Configure MSDP on each RP router.

Configure anycast PIM with the rp-set statement on each RP router.

Configure anycast PIM with the rp-set statement on each source DR router.

Configure MSDP on each source DR router.

Exhibit Referring to the exhibit, which two statements are correct about the dual route reflectors within a cluster? (Choose two.)

RR1 and RR2 append the duster ID when advertising routes from dient to dient.

RR1 and RR2 advertise routes learned from the clients to EBGP peers, using itself as the next hop.

RR1 and RR2 must have the same duster ID to exchange routes learned from the client.

RR1 and RR2 append the duster ID when advertising routes from dient to dient.

RR1 and RR2 advertise routes learned from the clients to EBGP peers, using itself as the next hop.

RR1 advertises routes from the client to RR2. using itself as the next hop.

You want to ensure that a single-area OSPF network will be loop free.In this scenario, what are two requirements that satisfy this requirement? (Choose two.)

The Shortest Path First algorithm must prune looped paths.

All nodes within an area must have the same information in their LSDBs.

The DR/BDR ensures that each node within an area has the same information in their LSDBs.

The Shortest Path First algorithm must prune looped paths.

Nodes within an area must connect in a full mesh.

All nodes within an area must have the same information in their LSDBs.

Which three statements about IS-IS in a multi-area network are correct? (Choose three.)

Internal L1 PDUs are flooded to the local area's L2 routers.

External L2 PDUs are flooded to all L2 routers in other areas.

Internal L1 PDUs are only flooded to the local area's L1 routers.

Internal L1 PDUs are flooded to the local area's L2 routers.

External L2 PDUs are flooded to all L2 routers in other areas.

Internal L1 PDUs are flooded to all L1 routers in other areas.

Internal L1 PDUs are only flooded to the local area's L1 routers.

External L2 PDUs are only flooded to the local area's L2 routers.

Refer to the exhibit. Click the Exhibit button.You have an OSPF environment. You have recently added a router called R4 that is directly connected to R1 and R2. You discover that R4 is only peering with R2.Referring to the exhibit, how would you correct the peering?

Adjust the Dead Interval on R4 to match the Dead Interval on R1 and R2.

Adjust the Priority on R1 to be lower than the Priority on R4.

Change the MTU size on R1 and R2 to be 22 bytes higher than R4's MTU size.

Adjust the Dead Interval on R4 to match the Dead Interval on R1 and R2.

Adjust the Hello Interval on R1 and R2 to match the Hello Interval on R4.

A router running IS-IS is configured with an ISO address of 49.0001.00a0.c96b.c490.00.Which part of this address is the system ID?

00a0.c96b.c490 is the system identifier.

0001.00a0.c96b.c490 is the system identifier.

c96b.c490 is the system identifier.

You are using a Layer 3 VPN to connect two customer sites. The VPN routes for the customer networks appear as hidden in the bgp. 13vpn. o routing table on the PE routers.What is causing this problem?

There is not an established MPLS LSP between the two PE routers.

The routes use overlapping IP addresses.

There is not an established MPLS LSP between the two PE routers.

There is a routing loop in the service provider backbone.

Route targets are not configured.

Refer to the exhibit. Click the Exhibit button.Which two statements are correct about the class-of-service configuration shown in the exhibit? (Choose two.)

Incoming traffic will not be classified because no classifier exists in the configuration.

The best-effort queue can transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, if no other queue is using that bandwidth.

Incoming traffic will not be classified because no classifier exists in the configuration.

The best-effort queue can transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, if no other queue is using that bandwidth.

Incoming traffic will be classified using the default classifier.

The best-effort queue can never transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, even if that bandwidth is available.

Which two statements are correct regarding the PIM DR in a PIM-SM domain? (Choose two.)

The source DR sends PIM register messages from the source network to the RP.

The receiver DR sends PIM join and PIM prune messages from the receiver network toward the RP.

The source DR sends PIM register messages from the source network to the RP.

If the DR priorities match, the router with the lowest IP address is selected as the DR.

The receiver DR sends PIM join and PIM prune messages from the receiver network toward the RP.

By default, PIM DR election is performed on point-to-point links.

Refer to the exhibit. Click the Exhibit button.Referring to the exhibit, you must provide VRF Internet access over a single connection for VPN-A Site 1, which connects to PE-1.Which two statements are correct in this scenario? (Choose two.)

You must use the RIB group to move a default route, which is learned through BGP, from the inet. o table to the VPN-A. inet. 0 table.

You do not need to use the RIB group to move interface routes from the inet. o table to the VPN-A. inet. 0 table.

You must use the RIB group to move a default route, which is learned through BGP, from the inet. o table to the VPN-A. inet. 0 table.

You do not need to use the RIB group to move interface routes from the inet. o table to the VPN-A. inet. 0 table.

You do not need to use the RIB group default route, which is learned through BGP, from the inet. o table to the VPN-A. inet. 0 table.

You must use the RIB group to move interface routes from the inet . 0 table to the VPN-A. inet. 0 table.

You have an L2VPN connecting two CEs across a provider network that runs OSPF. You have OSPF configured on both CEs.Which two statements are correct in this scenario? (Choose two.)

The CE and PE OSPF areas can be different.

OSPF neighborship is formed between the two CEs.

OSPF neighborship is formed between the CEs and PEs.

The CE and PE OSPF areas can be different.

The CE and PE OSPF areas must match.

OSPF neighborship is formed between the two CEs.

Juniper JN0-664 Practice Test 2 - Free Online Exam Prep & Questions

Question 1 / 40

Exhibit

Juniper JN0-664 image Question 41 51108 09182024211332000000

You want to use both links between R1 and R2 Because of the bandwidth difference between the two links, you must ensure that the links are used as much as possible.

Which action will accomplish this goal?

Define a policy to tag routes with the appropriate bandwidth community.

Disable multipath.

Ensure that the metric-out parameter on the Gigabit Ethernet interface is higher than the 10 Gigibit Ethernet interface.

Enable per-prefix load balancing.

Comment (0)

Juniper JN0-664 Practice Test 2

Question

Juniper JN0-664 Practice Tests

Practice Tests