You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)

Use ports with the same chipsets.

Use ports with different chipsets.

Use ports with the same chipsets.

Click the Exhibit button. Which set of components on a FAS9000 are highlighted in the exhibit?

FCVI-Module, Controller, Serial-Port, FlashCache-Module

SAS-Module, Controller, USB-Port, FlashCache-Module

NVRAM-Module, Controller, Serial-Port, FlashCache-Module

Powersupply, Controller, USB-Port, NVRAM-Module

After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.In this scenario, which two commands would you use to accomplish this task? (Choose two.)

system node autosupport history show

system node autosupport check show

system node autosupport history show

system node autosupport check show

system node autosupport destination show

Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.Which two actions would enable the customer to accomplish this task? (Choose two.)

Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.

Deploy a new AFF A400 to the cluster.

Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.

Connect the new NS224 shelves to the existing Cisco Nexus 3232C switches.

Deploy a new AFF A400 to the cluster.

Deploy new, dedicated, storage switches for the new NS224 shelves.

Click the Exhibit button. After installation of a new ONTAP cluster, you experience a problem. You successfully create a support case on the NetApp Support site. The customer asks you how to view the status of the case.Referring to the exhibit, which two steps would allow the customer to accomplish this task? (Choose two.)

Open https://support.netapp.com, using the customer credentials.

Open My Cases, and select the 41747189 case number.

Open https://support.netapp.com, using the partner credentials.

Open https://support.netapp.com, using the customer credentials.

Open My Cases, and select the 41747189 case number.

Open My Cases, and select Create a Case.

Which command would be used to measure the throughput and latency of traffic between nodes?

qos statistics workload performance show

You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data ports.In this scenario, which two flow control settings would you verify? (Choose two.)

Verify that the data network ports have full flow control disabled.

Verify that the cluster network ports have full flow control enabled.

Verify that the data network ports have full flow control disabled.

Verify that the cluster network ports have full flow control enabled.

Verify that the data network ports have full flow control enabled.

Verify that the cluster network ports have full flow control disabled.

A customer wants to enable SnapMirror Synchronous across their environment. The customer must ensure that SnapMirror Synchronous will work across the environment.In this scenario, which two statements are true? (Choose two.)

A SnapMirror Synchronous license is required on both the source and destination clusters.

A SnapMirror license is not required on both the source cluster and the destination cluster.

A SnapMirror license is required on both the source cluster and the destination cluster.

A SnapMirror Synchronous license is required on both the source and destination clusters.

A SnapMirror license is not required on both the source cluster and the destination cluster.

A SnapMirror Synchronous license is required on the source cluster.

Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.In this scenario, which two methods would be supported to migrate the data? (Choose two.)

Perform a controller swap from the FAS8020 to the AFF A250s.

Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems.

Perform a controller swap from the FAS8020 to the AFF A250s.

Create a 4-node cluster on one side and use the vol move command to migrate the data.

Use a host-based copy migration method.

Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems.

You are deploying a new AFF All SAN Array A250 into a customer's existing data fabric.In this scenario, which two tools would give insight into their existing Cisco MDS fabric configuration?(Choose two.)

Cisco Data Center Network Manager (DCNM)

You are preparing to install a new 2-node AFF A250 system at a customer site with an existing cluster that uses NetApp CN1610 cluster interconnect switches.In this scenario, what are two valid actions for this installation? (Choose two.)

Create a new 2-node switched cluster that uses the CN1610 cluster switches.

Migrate the existing cluster to new switches and add the new nodes.

Add the new nodes to the existing cluster and switches.

Create a new 2-node switched cluster that uses the CN1610 cluster switches.

Create a new 2-node switchless cluster.

Migrate the existing cluster to new switches and add the new nodes.

Click the Exhibit button. You are attempting to add a new ONTAP 9.7 node to your ONTAP 9.8 NetApp cluster. After attempting to add the node, it fails as shown in the exhibit.What are two nondisruptive ways to add the new node to your ONTAP cluster? (Choose two.)

Upgrade the new node from ONTAP 9.7 to ONTAP 9.8.

Add the node using the -allow-mixed-version- parameter.

Revert the cluster from ONTAP 9.8 to ONTAP 9.7.

Re-initialize all the nodes in the ONTAP cluster with ONTAP 9.7.

Upgrade the new node from ONTAP 9.7 to ONTAP 9.8.

Add the node using the -allow-mixed-version- parameter.

Click the Exhibit button. You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster pingcluster node1 command and received the output as shown in the exhibit.Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)

2 paths up, 0 paths down (TCP check)

basic connectivity succeeds on 4 path(s)

2 paths up, 0 paths down (TCP check)

2 paths up, 0 paths down (UDP check)

larger than PMTU communication succeeds on 4 path(s)

basic connectivity succeeds on 4 path(s)

You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.In this scenario, how would you add the shelf?

Add the shelf to the existing stack.

Create a new stack on the HA pair to add the shelf.

Connect the shelf to an HA pair with NSE drives.

License NSE and add the shelf to this HA pair as a new stack.

You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

Cable the AFF A250 nodes to the breakout ports on the switch.

Load the Cluster-HA-Breakout RCF.

Cable the AFF A250 nodes to the next free ports on the switch.

Cable the AFF A250 nodes to the breakout ports on the switch.

Load the Cluster-HA-Breakout RCF.

You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.In this scenario, which two statements are true? (Choose two.)

The AFF A250 uses different ports for the cluster and the HA interconnect.

The AFF A250 requires switches with 25GbE port support.

The AFF A250 requires switches with 40GbE port support.

The AFF A250 uses different ports for the cluster and the HA interconnect.

The AFF A250 requires switches with 25GbE port support.

The AFF A250 uses the same port for the cluster and the HA interconnect.

Click the Exhibit button. What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)

to provide a direct connection for the SnapMirror Synchronous (SM-S)

to provide connectivity for NVRAM over iWARP

to provide a direct connection for the SnapMirror Synchronous (SM-S)

to install cross-site cluster management switches

to provide connectivity for NVRAM over iWARP

to enable SyncMirror replication

Network Appliance NS0-184 Practice Test 1 - Free Online Exam Prep & Questions

Question 1 / 40

Click the Exhibit button.

Network Appliance NS0-184 image Question 1 79153 09232024011634000000

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.

Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

a 10GbE SFP+ to SFP+ cable

a 100GbE QSFP28+ to 4x25GbE SFP28+ cable

a 40GbE QSFP+ to QSFP+ cable

a 40GbE QSFP+ to 4x10GbE SFP+ cable

Comment (0)

Network Appliance NS0-184 Practice Test 1

Question

Network Appliance NS0-184 Practice Tests

Practice Tests